82 VQT2M98 VQT2M98 83
Meanings and required responses to major messages displayed on LCD monitor.
Message displays
[THIS MEMORY CARD CANNOT BE USED]
A MultiMediaCard was inserted.
Not compatible with the camera. Use a compatible card.
[THIS MEMORY CARD IS WRITE-PROTECTED]
Unlock the write-protect switch on the card. (11)
[NO VALID PICTURE TO PLAY]
Take pictures, or insert a different card already containing pictures.
[THIS PICTURE IS PROTECTED]
Release the protection before deleting, etc. (72)
[SOME PICTURES CANNOT BE DELETED] [THIS PICTURE CANNOT BE DELETED]
Non-DCF pictures (31) cannot be deleted.
Save needed data on a computer or other device, and then use [FORMAT] on the camera to
erase the card. (21)
[NO ADDITIONAL SELECTIONS CAN BE MADE]
The number of pictures that can be deleted at once has been exceeded.
More than 999 pictures have been set as [FAVORITE].
The number of pictures allowing [TEXT STAMP] or [RESIZE] (multiple settings) at once has been
exceeded.
[CANNOT BE SET ON THIS PICTURE]
Pictures that do not conform to DCF standards cannot be used for [PRINT SET] and [TEXT
STAMP].
[PLEASE TURN CAMERA OFF AND THEN ON AGAIN] [SYSTEM ERROR]
The lens is not working correctly.
Turn on power again.
(Consult the dealer or your nearest Service Center if display still remains)
[SOME PICTURES CANNOT BE COPIED] [COPY COULD NOT BE COMPLETED]
Pictures cannot be copied in following cases.
Picture of same name already exists in built-in memory when copying from card.
File is not of DCF standard.
Picture taken or edited on a different device.
[NOT ENOUGH SPACE ON BUILT-IN MEMORY] [NOT ENOUGH MEMORY ON THE CARD]
There is no space left on the built-in memory or the card. When you copy pictures from the built-in
memory to the card (batch copy), he pictures are copied until the capacity of the card becomes full.
[BUILT-IN MEMORY ERROR] [FORMAT BUILT-IN MEMORY?]
Displayed when formatting built-in memory via computer, etc.
Reformat directly using camera. Data will be deleted.
[MEMORY CARD ERROR] [FORMAT THIS CARD?]
The card format cannot be used with this camera.
Save needed data on a computer or other device, and then use [FORMAT] on he camera. (21)
[INSERT SD CARD AGAIN] [TRY ANOTHER CARD]
Access to card has failed.
Insert card again.
Try with a different card.
[MEMORY CARD ERROR] [MEMORY CARD PARAMETER ERROR]
Card is not of SD standard.
When cards in capacities of 4 GB or more are used, only SDHC or SDXC memory cards are
supported.
[READ ERROR]/[WRITE ERROR] [PLEASE CHECK THE CARD]
Data read has failed.
Check whether card has been inserted correc ly (10).
Data write has failed.
Turn off power and remove card, before re-inserting and turning on power again.
Card may possibly be damaged.
Try with a different card.
[MOTION RECORDING WAS CANCELLED DUE TO THE LIMITATION OF THE WRITING
SPEED OF THE CARD]
When recording motion picture, use a card rated with an SD speed class
of ‘Class 6’ or higher.
SD speed class refers to a specification for sustained write speeds.
If recording stops even when using a card with speed of ‘Class 6’ or faster, the data wri ing speed is
low. We recommend backing up the data on the memory card and reformatting it. (21)
Motion picture recording may be automatically terminated with certain cards.
[A FOLDER CANNOT BE CREATED]
Folder numbers in use have reached 999.
Save needed data on a computer or other device, and then use [FORMAT] on he camera. (21)
[PICTURE IS DISPLAYED FOR 16:9 TV] [PICTURE IS DISPLAYED FOR 4:3 TV]
AV cable is connected to camera.
To remove message immediately Press [MENU/SET].
To change aspect ratio Change [TV ASPECT] (21).
USB connection cable is only connected to camera.
Message disappears when cable is also connected to another device.
[THIS BATTERY CANNOT BE USED]
Use a genuine Panasonic battery.
Battery cannot be recognized as terminal is dirty.
Wipe any dirt away from the battery terminal.
[NO BATTERY POWER REMAINS]
The battery level is low.
Charge the battery before use. (8)
To Next Page
Loading...
Need help?
General
