Panasonic PT-AE4000E

Technical Information
44 -
E
NGLISH
▲
Command Control contents Remarks
VXX
LENS MEMORY LOAD
Loads LENS MEMORY.
LMLI0 = +00000 = LENS MEMORY 1 LMLI0 = +00001 = LENS MEMORY 2
LMLI0 = +00002 = LENS MEMORY 3 LMLI0 = +00003 = LENS MEMORY 4
LMLI0 = +00004 = LENS MEMORY 5 LMLI0 = +00005 = LENS MEMORY 6
GAMMA ADJUSTMENT
Sets Y ADJUST. (OUTPUT)
AGOS0 = p1p2d1d2d3d4
p1p2 = POINT (01 - 09) d1d2d3d4 = OUTPUT (0000 - 0255)
Sets R ADJUST. (OUTPUT)
AGOS1 = p1p2d1d2d3d4
p1p2 = POINT (01 - 09) d1d2d3d4 = OUTPUT (0000 - 0255)
Sets G ADJUST. (OUTPUT)
AGOS2 = p1p2d1d2d3d4
p1p2 = POINT (01 - 09) d1d2d3d4 = OUTPUT (0000 - 0255)
Sets B ADJUST. (OUTPUT)
AGOS3 = p1p2d1d2d3d4
p1p2 = POINT (01 - 09) d1d2d3d4 = OUTPUT (0000 - 0255)
Sets GAMMA ADJUSTMENT. (INPUT)
AGIS0 = p1p2d1d2d3
p1p2 = POINT (01 - 09) d1d2d3 = INPUT (001 - 099)
TRIGGER 1 (OUTPUT)
Switches TRIGGER 1 (OUTPUT) when RS-232C COMMAND LINK is set in the
TRIGGER 1 SETTING menu.
TROI0 = +00000 = LOW TROI0 = +00001 = HIGH
TRIGGER 2 (OUTPUT)
Switches TRIGGER 2 (OUTPUT) when RS-232C COMMAND LINK is set in the
TRIGGER 2 SETTING menu.
TROI1 = +00000 = LOW TROI1 = +00001 = HIGH
J
Inquiry commands
Command Control contents Parameter
QPW
Power status 000 = OFF 001 = ON
QFZ
FREEZE status 0 = OFF 1 = ON
QIN
INPUT signal status
CP1 = COMPONENT IN
SVD = S-VIDEO IN VID = VIDEO IN
HD1 = HDMI1 IN HD2 = HDMI2 IN
HD3 = HDMI3 IN RG1 = COMPUTER IN
QOT
OFF TIMER status
0 = OFF
1 = 60 min. 2 = 90 min. 3 = 120 min. 4 = 150 min.
5 = 180 min.
6 = 210 min. 7 = 240 min.
QPM
PICTURE MODE status
NOR = NORMAL DYN = DYNAMIC CL1 = COLOUR1 CL2 = COLOUR2
CN1 = CINEMA1 CN2 = CINEMA2 CN3 = CINEMA3
QSH
BLANK status 0 = OFF 1 = ON
QWM
WAVEFORM status
0 = OFF
1 = FULL SCAN (Y) 5 = SINGLE LINE SCAN (Y)
2 = FULL SCAN (R) 6 = SINGLE LINE SCAN (R)
3 = FULL SCAN (G) 7 = SINGLE LINE SCAN (G)
4 = FULL SCAN (B) 8 = SINGLE LINE SCAN (B)
QVX
GAMMA ADJUSTMENT
status
AGOS0 = p1p2d1d2d3d4
p1p2 = POINT (01 - 09) d1d2d3d4 = OUTPUT (0000 - 0255)
AGOS1 = p1p2d1d2d3d4
p1p2 = POINT (01 - 09) d1d2d3d4 = OUTPUT (0000 - 0255)
AGOS2 = p1p2d1d2d3d4
p1p2 = POINT (01 - 09) d1d2d3d4 = OUTPUT (0000 - 0255)
AGOS3 = p1p2d1d2d3d4
p1p2 = POINT (01 - 09) d1d2d3d4 = OUTPUT (0000 - 0255)
AGIS0 = p1p2d1d2d3
p1p2 = POINT (01 - 09) d1d2d3 = INPUT (001 - 099)