Panasonic SA-PM91DEE

Item Operational Condition
and Key Function
Details Display To Exit Mode
Measurement of CD
laser current
electricity
While the player is
stopped and no disc is
inserted, press and
hold down the [STOP]
button on the player
and the number button
“3” on the remote
controller unit.
Measurement of CD laser current
electricity
Measures CD laser current electricity
and displays the result together with
the initialization value stored in
EEPROM. After measurement, CD
laser is lit till the power is turned off (or
goes off when the primary power is
turned off).
[xxx_yyy_DC]
DC : CD laser current electricity
measurement mode
xxx : Current electricity initialization
value stored in EEPROM
yyy : Present value of current
electricity
Values are shown in the decimal
digit. The above example indicates
the current electricity initialization
value is xxx mA and its present
value is yyy mA when laser is turned
on.
Automatically exits
the mode after five
seconds.
Display the device
name
While the player is
stopped and no disc is
inserted, press and
hold down the [STOP]
button on the player
and the number button
“4” on the remote
controller unit.
Display the device name [xxxxxxxxxx] Automatically exits
the mode after five
seconds.
Jitter display While the player is
stopped and no disc is
inserted, press and
hold down the [STOP]
button on the player
and the number
button, “5” on the
remote controller unit.
Jitter display
Measures and displays jitter.
Measurement is repeated every
second. Read error counter starts at 0
at the mode setting, and increased by
one as data read fails at target block. A
small defect is allowed to correct by
retry. Any possibility is counted as one
increment. Repetitive errors after retry
increase by two levels or more.
[xxx_yyy_zz]
xxx : Jitter measurement value
yyy : Read error counter
zz : Focus driving value
Values are shown to one decimal
place in the decimal digit.Focus
driving value is displayed in the
hexadecimal digit.
Press the STOP.
Region display While the player is
stopped and no disc is
inserted, press and
hold down the [STOP]
button on the player
and the number
button, “6” on the
remote controller unit.
Region display [u__w_xy_zzz]
w : Region number
u x : N noPAL P PAL
y: N NTSC 6 PAL60
zzz: Paneconjampa information
Automatically exits
the mode after five
seconds.
Firm version display While the player is
stopped and no disc is
inserted, press and
hold down the [STOP]
button on the player
and the number
button, “7” on the
remote controller unit.
Firm version display [srrrxxyzzz]
s : Model type of Panecon
rrr : Release number of Panecon
xxx : Generation of Shiscon (26)
y : Model type of Shiscon
zzz : Release number of Shiscon
Automatically exits
the mode after five
seconds.
Region and firm
display
While the player is
stopped and no disc is
inserted, press and
hold down the [STOP]
button on the player
and the number
button, “8” on the
remote controller unit.
Region and firm version display [__r__xyzzz]
r : Region number
x : Generation of Shiscon
y : Model type of Shiscon
zzz : Release number of Shiscon
Automatically exits
the mode after five
seconds.
User initialization While the player is
stopped and no disc is
inserted, press and
hold down the [STOP]
button on the player
and the number button
on the remote
controller unit.
User initialization
The user setting recovers the factory
setting.
[_INITIALIZE_] Automatically exits
the mode after five
seconds.
DVD reset While the user
initialization, press and
hold down the [STOP]
button on the player
and the number button
“ENTER” on the
remote controller unit.
DVD reset
The user setting is returned in the state
of the factory shipment. It doesn´t
initialize it at the time of the laser and
the time of the spindle to develop a
model table initial value of the
corresponding number referring to
Paneconjampa.
[_DVD_RESET_ _] Automatically exits
the mode after five
seconds.
60
SA-PM91DEE