English
82
■ [Power management mode]: [On]
The following fixed values are set to the menu of
power consumption reduction. Individual setting is not
available.
[No signal power off]: [Enable]
[HDMI1 power management]: [On]
[HDMI2 power management]: [On]
[DVI-D power management]: [On]
[PC power management]: [On]
[Power save]: [On]
■ [Power management mode]: [Custom]
The menu of the power consumption reduction is
individually set. This setting is enabled when [Power
management mode] is set to [Custom].
[No signal power off]
When this is set to [Enable], the power supply of the
unit goes off automatically (standby) when there is no
operation or sync signal for about 10 minutes.
Note
●
With the USB input, the unit determines no signal is
present when the USB memory is not connected to
the USB terminal.
●
The OpenPort PLATFORM input is not a target of the
“no signal” detection.
[HDMI1 power management]
[HDMI2 power management]
When this function is set to [On], it operates under
the following conditions to turn the power on or off
automatically.
When no pictures (sync signal) are detected for
60 seconds or so at HDMI1 or HDMI2 input:
Power is turned off (sleep); the power indicator
lights up orange.
When pictures (sync signal) are subsequently
detected:
Power is turned on; the power indicator lights up
green.
Note
●
For TH-55AF1U, TH-49AF1U and TH-42AF1U,
when the power is turned off, the OpenPort
PLATFORM system is shutdown once, and then
restarted. During that time (approx. 60 seconds),
the power on processing by detecting pictures
(sync signal) is not accepted.
[DVI-D power management]
When this function is set to [On], it operates under
the following conditions to turn the power on or off
automatically.
When no pictures (sync signal) are detected for
60 seconds or so at DVI-D input:
Power is turned off (sleep); the power indicator
lights up orange.
When pictures (sync signal) are subsequently
detected:
Power is turned on; the power indicator lights up
green.
Note
●
For TH-55AF1U, TH-49AF1U and TH-42AF1U,
when the power is turned off, the OpenPort
PLATFORM system is shutdown once, and then
restarted. During that time (approx. 60 seconds),
the power on processing by detecting pictures
(sync signal) is not accepted.
[PC power management] (DPMS function)
When this function is set to [On], it operates under
the following conditions to turn the power on or off
automatically.
When no pictures (HD/VD sync signals) are
detected for 60 seconds or so at PC input:
Power is turned off (sleep); the power indicator
lights up orange.
When pictures (HD/VD sync signals) are
subsequently detected:
Power is turned on; the power indicator lights up
green.
Note
●
This function is effective when [Sync] in [Signal] is
set to [Auto] or [HV sync] and [Component/RGB-in
select] are set to [RGB]. (see page 78)
●
For TH-55AF1U, TH-49AF1U and TH-42AF1U,
when the power is turned off, the OpenPort
PLATFORM system is shutdown once, and then
restarted. During that time (approx. 60 seconds),
the power on processing by detecting pictures (HD/
VD sync signals) is not accepted.
[Power save]
This function adjusts the brightness of the backlight to
reduce power consumption.
[Off]:
This function does not operate.
[On]:
Backlight brightness is reduced.
Note
●
If [Input search] is set to items other than [Off], the
[Input search] function is prioritised. (The “Power
management” function does not operate for each
terminal.) (For details of [Input search] function,
see page 88.)
●
If [Failover/Failback] - [Input change mode] is set
to items other than [Off], the [Failover/Failback]
function is prioritised. (The “Power management”
function does not operate for each terminal.) (For
details of [Failover/Failback] function, see page
89.)
To Next Page
Loading...
