Panasonic WV-CW590G

7
2. Move the cursor to →PUSHSETtotherightofPAN/
TILT, and then press the CAM (SET) button to
displaythePAN/TILTsettingmenu.
3. Use the joystick to position the camera, and then
presstheCAM(SET)button.
4. Move the cursor to → PUSH SET to the right of
ZOOM/FOCUS, and then press the CAM (SET)
buttontodisplaytheZOOM/FOCUSsettingmenu.
5. Move the joystick left, right, up and down to adjust
the position of the lens focus, and then press the
CAM(SET)button.
l Adjusting Camera Position When
Changing Cameras (PAN OFFSET SET)
The system controller etc. has a function for
downloading (saving) and uploading (recovering)
setting information for the camera. This function allows
you to upload (recover)original setting information that
hasbeendownloaded(saved)beforesomeunforeseen
damage or malfunction causes setting information in the
camera to be lost. However, there may be some slight
differences in images from those uploaded (recovered)
when the camera is changed. The "PAN OFFSET SET"
function is for adjusting these differences.
1. Alignthecursorwith"PANOFFSETSET"withthe← or
→arrow, and presstheCAM (SET) button toset the
offset value.
Set the offset value to 0.0, or in a range of -10.0 to
+10.0.Allpresetpositionsforthecamera'sposition
are adjusted according to the offset value.
Important:
•Data is not compatible with existing cameras.
Uploading setting information from existing
cameras will damage data in the camera. If data
in the camera is damaged, download camera
setting information from a camera that still has the
factory settings and then upload it to the camera
with the damaged data.
l Preset ID Setting (PRESET ID)
The preset ID is a series of alphanumeric characters
that indicate the location of the camera.
1. Move the cursor to PRESET ID, and then tilt the
joystickleft or right totoggle presetID display ON
andOFF.
2. Select ON or OFF, and then press the CAM (SET)
button.
  ThefactorydefaultsettingisON. 
This will display the preset ID setting menu.
Please see page 15 for details on DEL.
→ PUSH SET
→ PUSH SET
**POSITION 1* **
PAN/TILT
ZOOM/FOCUS
TILT / PAN
PAN OFFSET SET
← 0.0 →
RET TOP
PRESET NO. 1
POSITION SET
PRESET ID
RET TOP DEL
ON
→ PUSH SET
→ PUSH SET
**POSITION 1* **
PAN/TILT
ZOOM/FOCUS
PAN OFFSET SET
← 0.0 →
RET TOP
ZOOM / FOCUS
→PUSH SET
**POSITION 1* **
PAN/TILT
ZOOM/FOCUS
PAN OFFSET SET
← 0.0 →
RET TOP
→PUSH SET
Notes:
 • Focusingmaybedifficult,becauseofthedistortion
caused by the curve of the dome cover, when the
cameraisatananglethatisclosetohorizontal.
 • Adifferentpositionnumbercanbeselectedby
moving the cursor to the position number at the top
of the position setting menu and tilting the joystick
leftandright.PressingtheCAM(SET)buttonwill
change to the setting screen for the newly selected
position number.
→PUSH SET
→PUSH SET
**POSITION 1* **
PAN/TILT
ZOOM/FOCUS
PAN OFFSET SET ← 0.0 →
RET TOP
Align the cursor here
 • ThecurrentlyregisteredcameraIDandpresetID
appear at the bottom of the position setting menu.
 • WhenusingasystemdeviceotherthantheWV-CU650/
CU950*, WJ-HD309A/HD316A over 65 position
numberscannotbeset.(asofSeptember2005)
  *Operation proceduremay vary depending on the
version of the system controllers software.
  ForVer.1.xx or earlier: only camera function
operations are supported
  For Ver.2.xx or later: preset/PGM preset button is
also supported.