Paradox SP6000 Installation Guide

Magellan & Spectra SP • Installation Guide
49
Reporting and Dialer settings
The following section explains all the features and options that must be programmed in order for your security system to properly report system events to a
monitoring station. When an event (e.g. zone in alarm) occurs in the system, the control panel verifies if a report code was programmed in the section
corresponding to the event (except Ademco Contact ID “All Codes”). If a report code was programmed, the control panel will dial the monitoring station telephone
number defined by the Event Call Direction feature. When the monitoring station answers, the control panel will transmit the System Account Code, followed by the
programmed report code.
Zone Reporting Codes
Sections [141] to [172]
A report code can be programmed for each of the available 32 zones. When an alarm, alarm restore, tamper, or tamper restore occurs on a zone, the control panel
can send the appropriate report code to the monitoring station.
User Reporting Codes
Sections [471] to [502]
A report code can be programmed for each of the available 32 users. When a user arms, disarms or cancels an alarm, the control panel can send the appropriate
report code to the monitoring station.
Special Arming Report Codes
Sections [860] and [861]
When the system is armed using one of the special arming features listed below, the control panel can send the appropriate report code to the monitoring station
identifying how the system was armed.
Section [860]
• Auto-Arming: A partition has armed itself at the programmed time.
• Late to Close: Reports every day at the time specified by the Auto-arm Timer.
• No Movement: No movement has been detected for the programmed amount of time in the partition.
• Partial Arming: A partition was Stay, Sleep, or Force armed or armed with Bypassed zones.
Section [861]
• Quick Arming: A partition was armed using a One-touch arming feature.
• Arming via PC: A partition was armed using the BabyWare software.
•N/A
•N/A
Special Disarming Report Codes
Section [862]
When using one of the special disarming features, the control panel can send the report code to the monitoring station, identifying how the system was disarmed.
• Cancel Auto-Arm: A partition is disarmed during the Timed Auto-arm's 60-second exit delay. Only reports if Disarming Reporting Options are set to always
report disarming.
• Disarming via PC: System is disarmed using the BabyWare soft ware. Only reports if Disarming Reporting Options are set to always report disarming.
• Cancel alarm with user or BabyWare: An alarm is canceled using the BabyWare software.
• Cancel Paramedic Alarm: A paramedic alarm is canceled.
Special Alarm Report Codes
Sections [863] and [864]
When the system generates an alarm due to one of the conditions listed below, the control panel can send the appropriate report code to the monitoring station
identifying the type of alarm.
Section [863]
• Emergency Panic: Panic keys [1] and [3] have been pressed.
• Auxiliary Panic: Panic keys [4] and [6] have been pressed.
• Fire Panic: Panic keys [7] and [9] have been pressed.
• Recent Closing: Reports when an alarm is generated after arming the system within period defined by the Recent Close Delay.
Section [864]
• Zone Shutdown: A zone communicates more than the programmed number of transmissions in a single armed period.
• Duress: A Duress access code is keyed in.
• Keypad Lockout: If a consecutive number of invalid codes are entered into a keypad, the control panel can be set to deny access from all keypads for a
specified period.
• Paramedic Alarm: A parademic alarm is sent to the monitoring station.

Paradox SP6000 Specifications

General

Partitions	2
User Codes	32
Event Buffer	256 events
PGM Outputs	2 (expandable to 16)
Compatibility	Compatible with wireless expansion modules and keypads
Communication	Phone line, GSM, IP
Users	32
Zones	Up to 32 (5 on-board)
Keypads	Supports multiple keypad types