13
English
Notes:
– PLUG and PLAY will be reinitiated again during
the next power up if :
i) PLUG and PLAY installation was not completed.
ii) No stereo frequency being detected during
PLUG and PLAY, "CHECK ANTENNA" will be
displayed.
–You can store any radio stations manually or
automatically after PLUG and PLAY.
– When PLUG and PLAY is used, all previously
stored radio stations will be replaced.
– During PLUG and PLAY, if no button is pressed
within 15 seconds, the system will go to
demonstration mode (if demonstration mode is
enable)
Demonstration mode
The system has a demonstration mode that
shows the various features offered by the system.
To disable the demonstration mode
● Press and hold Ç (on the system only) for 5
seconds when the system is in demonstration
mode.
➜ "DEMO OFF" is displayed.
➜ The system will switch to standby mode.
To enable the demonstration mode
● Press and hold Ç (on the system only) for 5
seconds when the system is in standby mode.
➜ The demonstration will begin.
Notes:
– If the demonstration mode has not been disabled,
it will resume 5 seconds later after the system
switches to standby mode.
– When the system is switched on from the main
power outlet, the CD changer tray may open and
close again to initialize the set.
– Even though the AC power cord is removed from
and reconnected to the wall socket, the
demonstration will remain off until it is switched on
again.
Switching the system ON
¶ Press CD, TUNER, TAPE or AUX.
You can also switch on the system by pressing
any one of the CD DIRECT PLAY buttons.
Switching the system to standby
mode
¶ Press STANDBY-ON or B on the remote
control.
➜ The system will switch to standby mode.
Switching the system to ECO
POWER standby mode
(when
Demonstration mode is stopped)
¶ Press ECO POWER or press and hold B on
the remote control for more than 2 seconds to
switch to eco power standby mode (< 2 watts).
➜ "ECO PWR" will be displayed, after which the
display screen goes blank.
➜ The ECO POWER LED will be lit.
To switch on the system from ECO
POWER mode
¶ Press ECO POWER.
➜ The system will switch to last selected source.
¶ Press CD, TUNER, TAPE or AUX on the
remote control
➜ The system will switch to the selected source.
Note:
– If the demonstration mode has not been
disabled, it will resume 5 seconds later.
Operating the System
14
English
Selecting the Source
¶ Press the respective source selection button: CD,
TUNER, TAPE or AUX.
➜ The display indicates the selected source.
Note:
–For an external source, make sure you have
connected the audio left and right OUT terminals
of the external equipment (TV, VCR, Laser Disc
player, DVD player or CD Recorder) to the AUX IN
terminals.
DIM mode
(only on remote control)
You can select the desired brightness for the
display.
¶ Press DIM to select DIM 1, DIM 2, DIM 3 or
DIM OFF display mode.
➜ The
DIM
appears on the display.
➜ "DIM 1", "DIM 2", "DIM 3" or "DIM OFF"
will be displayed depending on the mode
selected.
DIM OFF - normal brightness with
Spectrum Analyzer On
DIM 1 - normal brightness with Spectrum
Analyzer Off
Volume Control
Adjust VOLUME to increase or decrease the
sound level.
For Personal Listening
Connect the headphones plug to the n socket
at the front of the system. The speakers will be
muted.
Sound Control
For Optimal sound listening, you can only
select one of the following sound control at
a time : DSC, VEC or OPTIMAL SOUND
MIX.
DIGITAL SOUND CONTROL (DSC)
The DSC feature enables you to adjust the
system to suit your type of music.
1
Press to select the DSC feature.
➜ DSC led lights up.
2
Adjust the JOG to select the desired Digital
Sound Control setting : OPTIMAL, JAZZ, ROCK,
or TECHNO.
➜ The selected digital sound is encircled.
➜ "OPTIMAL, JAZZ, ROCK or TECHNO" will
be displayed.
Note:
–For neutral setting, select JAZZ.
Operating the System
To Next Page
Loading...
