19
English
Tuner
Note:
–For 'PLUG & PLAY' feature, please refer to page
12.
Tuning to radio stations
1
Press TUNER (BAND) to select TUNER mode.
➜ “TUNER” will be displayed.
A few seconds later, the current radio frequency
will be displayed.
2
Press TUNER (BAND) again to select the
desired waveband : FM, MW or LW.
3
Press à or á for more than one second, then
release.
➜ The display will show “SEARCH” until a radio
station with sufficient signal strength is found.
¶ Repeat this procedure until the desired station is
reached.
¶ To tune to a weak station, briefly press à or
á repeatedly until the display shows the
desired frequency and/or when the best
reception has been obtained.
Storing Preset Stations
You can store up to 40 radio stations in the
memory. When a preset radio station is selected,
the preset number appears next to the
frequency on the display.
Automatic programming
1
Press TUNER (BAND).
2
Press PROGRAM for more than one second.
➜ The PROG flag starts flashing and “AUTO” will
be displayed.
➜ The system will start searching for all radio
stations with RDS and then followed by radio
stations on FM, MW and LW band respectively.
➜ All available stations will be stored
automatically. The frequency and preset number
will be displayed briefly.
➜ The system will stop searching when all the
available radio stations are stored or when the
memory for 40 preset radio stations is used.
➜ The system will remain tuned to the last
stored preset radio station.
Notes:
–You can cancel the automatic programming by
pressing PROGRAM or
Ç
(on the system only).
– If you want to reserve a section of preset
numbers, for example preset numbers 1 to 9,
select preset 10 before starting automatic
programming, only the preset numbers 10 to 40
will be programmed.
20
English
Tuner
Manual programming
1
Press TUNER (BAND).
2
Press TUNER (BAND) again to select the
desired waveband : FM, MW or LW.
3
Press PROGRAM for less than one second.
➜ The PROG flag starts flashing.
➜ The next available preset number will be
displayed for selection.
4
Press à or á to tune to the desired frequency.
¶ If you wish to store the radio station to another
preset number, press 4 or 3 to select the
desired preset number.
5
Press PROGRAM again.
➜ The PROG flag disappears and the radio
station will be stored.
¶ Repeat steps 3 – 5 to store other preset radio
stations.
Notes:
– When 40 radio stations are stored and you
attempt to store another radio station, the display
will show "FULL”. If you want to change an
existing preset number, repeat steps 3 – 5.
–You can cancel manual programming by
pressing
Ç
(on the system only).
– During programming, if no button is pressed
within 20 seconds, the system will exit programme
mode automatically.
Tuning to Preset Radio Stations
¶ Press 4 or 3 to select the desired preset
number.
➜ The preset number, radio frequency, and
waveband appear on the display.
Receiving RDS Radio Station
Ç
RDS (Radio Data System) is a broadcasting
service that allows FM stations to send additional
information along with the regular FM radio
signal. This additional information can contain:
¶ STATION NAME: The radio station name is
displayed.
¶ PROGRAM TYPE: The following program
types exist and can be received by your tuner:
News, Affairs, Info, Sport, Educate, Drama,
Culture, Science, Varied, Pop M, Rock M, M.O.R.
(middle of the road music), Light M, Classics,
Other M, No type.
¶ RADIO TEXT (RT): text messages appear in
the display.
When you have tuned to a RDS station, the RDS
logo (Ç) and the radio station name will appear
on the display:
¶ The display normally shows the radio station
name if available.
By repeatedly pressing RDS button you can
change the type of display information:
➜ The display shows in turn:
STATION NAME ™ PROGRAM TYPE ™
RADIO TEXT ™ TUNED FREQUENCY ™
STATION NAME ...
Note:
– When you press the RDS button and the display
shows "
NO RDS
", it indicates that either the tuned
station is not transmitting RDS signal or it is a non
RDS station.
To Next Page
Loading...
