27
English
Clock/Timer
3
Press à or á on the system to set the hour
for the timer to start.
4
Press í or ë on the system to set the minute
for the timer to start.
5
Press CLOCK•TIMER to store the start time.
➜ The timer is now set.
➜ The
TIMER
remains on the display.
¶ At the preset time, the timer will be activated.
➜ The selected source will be played.
Notes:
– During timer setting, if no button is pressed
within 90 seconds, the system will exit timer setting
mode automatically.
– If the source selected is TUNER, the last tuned
frequency will be switched on.
– If the source selected is CD, playback will begin
with the first track of the selected disc or
programme. If the disc trays are empty, the TUNER
will be selected instead.
– The timer will not activate if a recording is in
progress.
To switch off the TIMER
1
Press and hold CLOCK•TIMER for more than
2 seconds.
2
Press Ç on the system to cancel the timer.
➜ The timer is now switched off.
➜ The display will show "OFF" and the
TIMER
disappears.
To start the TIMER again (for the same
preset time and source)
1
Press and hold CLOCK•TIMER for more than
2 seconds.
2
Press CLOCK•TIMER again to store the start
time.
➜ The timer is now on.
➜ The
TIMER
appears on the display.
Sleep Timer
(only on remote control)
This feature allows you to select a length of time
after which the system will switch to the standby
mode automatically.
1
Press SLEEP on the remote control repeatedly
to select a period of time.
➜ The selections are as follows (time in
minutes): 15
™™
™™
™ 30
™™
™™
™ 45
™™
™™
™ 60
™™
™™
™ OFF
™™
™™
™
15 …
➜ "SLEEP XX" or "OFF" will be displayed. "XX"
is the time in minutes.
2
When you reach the desired length of time, stop
pressing the SLEEP button.
➜ The
SLEEP
display lights up.
➜ The Sleep Timer is now set. Before the
system switches to standby mode, a countdown
of 10 seconds will be displayed.
"SLEEP 10"
™™
™™
™ "SLEEP 9"....
™™
™™
™ "SLEEP 1"
™™
™™
™ "SLEEP"
While SLEEP mode is activated
¶ Press SLEEP once to view the remaining length
of time.
¶ Press SLEEP twice to change the pre-selected
period of time.
➜ The display will show the remaining time
followed by the sequence of sleep timer options.
To switch off the Sleep Timer
¶ Press SLEEP repeatedly until "OFF" is displayed,
or press the STANDBY-ON button.
29
English
Troubleshooting
WARNING
Do not open the player as there is a risk of electric shock! Under no circumstances should
you try to repair the player yourself, as this will invalidate the warranty
If a fault occurs, first check the points listed below before taking the player for repair. If
you are unable to remedy a problem by following these hints, consult your dealer or
service centre.
Symptom Remedy
“NO DISC” is displayed. – If the disc is inserted upside down.
– Moisture condensation at the lens.
– There is no disc in the CD tray.
– The disc is dirty, badly scratched or warped.
– The disc lens is dirty or dusty, refer to section
under Maintenance.
“DISC NOT FINALIZED” is displayed. – The CD-RW or CD-R disc is not properly
recorded for use with a standard CD player.
– The disc is badly scratched or dirty.
Poor radio reception. – The signal is too weak, adjust the antenna or
connect an external antenna for better
reception.
– The TV or VCR is too close to the stereo
system.
Maintenance
Cleaning the Cabinet
¶ Use a soft cloth slightly moistened with a mild
detergent solution. Do not use a solution
containing alcohol, spirits, ammonia or abrasives.
Cleaning Discs
¶ When a disc becomes dirty,
clean it with a cleaning cloth.
Wipe the disc from the center
out.
¶ Do not use solvents such as
benzine, thinner, commercially
available cleaners, or antistatic
spray intended for analog records.
Cleaning the Disc lens
¶ After prolonged use, dirt or dust may
accumulate at the disc lens. To ensure good
playback quality, clean the disc lens with Philips
CD Lens Cleaner or any commercially available
cleaner. Follow the instructions supplied with
cleaner.
Cleaning the Heads and the Tape Paths
¶ To ensure good recording and playback quality,
clean the heads, the capstan(s), and pressure
roller(s) after every 50 hours of tape operation.
¶ Use a cotton swab slightly moistened with
cleaning fluid or alcohol.
¶ You can also clean the heads by playing a
cleaning tape once.
Demagnetizing the heads
¶ Use a demagnetizing tape available at your
dealer.
To Next Page
Loading...
