21
English
RDS Clock
Some RDS station may be transmitting a real
clock time at an interval of every minute.
Setting the time with RDS clock
1
Press CLOCK•TIMER.
➜ "--:--" or current time appears on the
display.
2
Press CLOCK•TIMER once more to enter
clock setting mode.
➜ "00
::
::
:00" or current time starts flashing.
3
Press RDS.
➜ The message "SEARCH RDS TIME" will be
displayed.
➜ If the current station is not receiving any RDS
information, "NO RDS TIME" will be displayed.
➜ When the RDS clock is read, "RDS TIME"
will be displayed. The current clock time is
displayed for 2 seconds and will be stored
automatically.
➜ If within 90 seconds, the RDS time is not
detected, "NO RDS TIME" will be displayed.
Note:
– Some RDS station may be transmitting a real
time clock at a minute interval. The accuracy of
the transmitted time depends on the transmitting
RDS station.
News
(only available in Radio Station with RDS)
You can activate NEWS function in Standby or
any source mode except Tuner mode. Once the
News PTY (program type) is detected in a RDS
station, it will switch to TUNER mode
automatically.
To start NEWS function
1
Press NEWS.
¶ The
NEWS
and "NEWS" will be displayed.
¶ It will scan stations stored in the first 5 preset
and wait for the News Program Type data to be
available in any of these RDS stations. During
the search :
➜ The current source activity will remain
uninterrupted.
➜ If no RDS station is found in the first 5
presets, the NEWS function will be switched off.
The display will show "NO RDS NEWS" and
NEWS
will disappear from the display.
¶ When NEWS transmission is detected, the
system will switch to Tuner mode.
➜ The
NEWS
starts flashing.
To cancel NEWS function
¶ Press NEWS again.
➜ The
NEWS
disappears and "NEWS OFF" will
be displayed.
Notes:
– If you are listening to a non RDS TUNER radio
station and should you decide to hear NEWS, first
select other source (e.g. CD, TAPE or AUX), then
press NEWS.
– Before using the NEWS feature, ensure that the
first 5 presets are RDS stations.
– The NEWS works only once for each activation.
– During News bulletin, you can press any
available source or Tuner function keys to cancel
NEWS function and execute the relevant source
mode.
– If set is switched to Tuner source, the NEWS
function will be cancelled, "
NEWS OFF
" will be
displayed immediately after the "
TUNER
"
message.
Tuner
22
English
Ta p e
Loading a tape
1
Press OPEN.
2
The tape deck door opens.
3
Load the tape with the open side downward and
the full spool to the left.
4
Close the tape deck door.
Auto Replay
¶ Press A. REPLAY to select either continuous
AUTO REPLAY or ONCE during tape playback.
➜ "AUTO REPLAY "(
) or "ONCE "(È) will
be displayed.
Notes:
– This feature is available during tape playback
only.
– When "
AUTO REPLAY
" is selected, the tape
will rewind automatically at the end of playback for
the selected side. Then it will start playing again. It
will replay up to a maximum of 20 times until you
press
Ç
.
– When "
ONCE
" is selected, the tape will play the
selected side once and then stop.
Ta pe Playback
1
Press TAPE (TAPE 1•2) to select TAPE mode.
➜ "TAPE 1" or "TAPE 2" will be displayed and
followed by "T1 222 " or "T2 222".
2
Load the tape into the selected tape deck.
3
Press PLAYÉÅ to start playback.
➜ "T1" or "T2" with "2" scrolling right will be
displayed.
¶ Press A.REPLAY to select the different type of
playback mode (see Auto Replay)
4
Press Ç to end playback.
➜ "T1" or "T2" with "222" will be displayed.
To Next Page
Loading...
