25
English
CD Synchro Start Recording
1
Load a blank tape into tape deck 2 and a disc
into a disc tray.
2
Press CD to select CD mode.
¶ You can program the tracks in the order you
want them to be recorded (see Programming
Tracks). If not, select the disc by pressing CD
(CD 1•2•3) and the tracks are recorded
according to the order on the selected disc.
3
Press RECORD to start recording.
➜ The REC starts flashing.
¶ Disc will start playback automatically.
4
Press Ç to stop recording.
Dubbing tapes
(from tape deck 1 to tape
deck 2)
1
Press TAPE ( TAPE 1•2 ) to select tape deck 2.
2
Load the prerecorded tape into tape deck 1 and
a blank tape into tape deck 2 with full spool to
the left.
3
Press DUBBING.
➜ "DUB" with "2" scrolling right will be displayed.
¶ Dubbing will start immediately.
➜ The REC starts flashing.
4
Press Ç to stop dubbing.
Notes:
– At the end of side A, flip the tapes to side B and
repeat the procedure.
– Dubbing of tapes is only possible from tape
deck 1 to tape deck 2.
–To ensure good dubbing, use tapes of the same
length.
–You can switch to other source while dubbing.
Recording from other sources
(only on tape deck 2)
1
Load a blank tape into tape deck 2 with the
open side downward.
2
Press CD, TUNER or AUX.
¶ Start playback of the selected source.
3
Press RECORD to start recording.
➜ The REC starts flashing.
4
Press Ç to stop recording.
Notes:
– During recording, it is not possible to listen to
another source.
Digital Recording via Digital Out
For CD digital recording, please refer to the
Instructions Manual of the CD Recorder, digital
audio equipment, etc.
Recording
View Clock
You can view the clock (if it is set) if the system
is in Standby mode or when any sound source is
selected (CD, TUNER, etc.). The clock will be
displayed for about seven seconds.
¶ Press CLOCK•TIMER briefly (on the system
only).
➜ “PM10:38 or 22:38” (the current time) will
be displayed depending on whether you have
selected 12- or 24-hour mode.
➜ “--:--” will be displayed if the clock is not
set.
Clock Setting
The clock can be set in either 12- or 24-hour
mode, e.g. “AM12:00“ or “00:00“. Before
setting the clock, you must be in the View Clock
mode.
1
Press CLOCK•TIMER to select clock mode.
2
Press PROGRAM to select 12- and 24- hour
mode.
➜ If 12-hour mode is selected, “AM12:00“
starts flashing.
➜ If 24-hour mode is selected, “00:00” starts
flashing.
3
Set the hour with à or á on the system.
4
Set the minute with í or ëon the system.
5
Press CLOCK•TIMER again to store the
setting.
➜ The clock starts.
¶ To exit without storing the setting, press Çon
the system.
Notes:
– During clock setting, if no button is pressed
within 90 seconds, the system will exit clock setting
mode automatically.
– When a power interruption occurs, the clock
setting is erased.
Timer Setting
¶ The system can switch on to CD , TUNER or
TAPE mode automatically at a preset time. It can
serve as an alarm to wake you up.
¶ Before setting the timer, make sure the clock is
set correctly.
¶ The timer will always be switched on once it is
set.
¶ The volume of the timer will increase
from the minimum level to the most
recently selected volume level.
1
Press and hold CLOCK•TIMER for more than
2 seconds to select timer mode.
➜ “AM12:00” or “00:00" or the last timer
setting starts flashing depending on whether y
ou
have selected 12- or 24-hour mode.
➜ The
TIMER
starts flashing.
➜ The selected source is lit while other available
sources are flashing.
2
Press CD , TUNER or TAPE to select the
desired source.
¶ Before selecting CD or TAPE, make sure a disc
or tape is loaded in the CD tray or tape deck 2.
To Next Page
Loading...
