Posch SpaltFix S-360 - User Manual

Questions and Answers

C
Cynthia HamptonAug 14, 2025
Why does the electric motor on my Posch Log Splitter fail to start or switch off frequently?
- J
  Joel WilsonAug 15, 2025
  If the electric motor on your Posch Log Splitter fails to start or switches off frequently, there might be several reasons. It could be due to a faulty power supply cable (have it examined by a specialist), incorrectly rated fuses (use correctly-rated fuses), a tripped motor circuit breaker (use a stronger power supply cable), or the wrong direction of rotation (swap over two phases).
M
Megan MarquezAug 17, 2025
Why is the hydraulic oil getting too hot in my Posch Log Splitter?
- P
  phubbardAug 18, 2025
  If the hydraulic oil in your Posch Log Splitter is getting too hot, it could be due to not enough hydraulic oil in the system (check the hydraulic oil level), poor quality hydraulic oil (change the hydraulic oil), or an unclean or blocked oil filter (change the filter insert).
J
Jessica GuzmanAug 21, 2025
What to do if my Posch Log Splitter loses power?
- C
  Catherine DennisAug 21, 2025
  Your Posch Log Splitter may be losing power due to the hydraulic oil getting too hot (refer to the "Hydraulic oil getting too hot" section) or not enough hydraulic oil in the hydraulic system (check the hydraulic oil level).
J
Jesse SmithAug 25, 2025
Why does the feed belt jerk or not move on my Posch Log Splitter?
- J
  Johnny MayoAug 25, 2025
  If the feed belt on your Posch Log Splitter jerks or does not move, the possible causes are: not enough hydraulic oil in the hydraulic system (check hydraulic oil level), poor quality hydraulic oil (change hydraulic oil), or the conveyor belt being too slack (tensioning the belt).
R
Rebecca HowardAug 28, 2025
Why is my Posch SpaltFix S-360 so noisy?
- J
  john91Aug 28, 2025
  If your Posch Log Splitter is making unusual noises, it may be because the PTO shaft is running too fast (adhere to the specified speed) or the oil filter is unclean or blocked (change the filter insert).
M
Margaret Hernandez DDSAug 31, 2025
Why does sawing require a great amount of power with my Posch SpaltFix S-360 Log Splitter?
- E
  Edward HernandezAug 31, 2025
  If sawing with your Posch Log Splitter requires a great amount of power, it could be due to a blunt saw blade (sharpen the saw blade), a loose saw blade (tighten the hexagon nut on the drive shaft), or a saw disc coated in resin (clean saw blade with a resin removing agent).
A
Amy NolanSep 4, 2025
What causes the conveyor belt to jerk or not move on my Posch SpaltFix S-360 Log Splitter?
- G
  Garrett HuntSep 4, 2025
  If the conveyor belt on your Posch Log Splitter jerks or does not move, it could be due to not enough hydraulic oil in the hydraulic system (check hydraulic oil level) or poor quality hydraulic oil (change hydraulic oil).
E
Edward GreenSep 6, 2025
Why is the hydraulic cylinder leaking on my Posch SpaltFix S-360?
- B
  Barbara CoxSep 6, 2025
  If the hydraulic cylinder on your Posch Log Splitter is leaking, it could be due to a worn sealing sleeve (renew sealing sleeves), a loose piston rod guide (retighten piston rod guide), or a damaged piston rod (renew piston rod).
L
lewismichaelSep 10, 2025
What to do if the switch does not work on my Posch SpaltFix S-360 Log Splitter?
- L
  Laura FreemanSep 10, 2025
  If the switch on your Posch Log Splitter does not work, it may be due to a faulty power supply cable (have the cable examined by a specialist), fuses keep tripping because of incorrectly rated fuse for power supply cable (use correctly-rated fuses), or a faulty contactor or motor circuit breaker (have the switch checked or send it in).