Proper Usage and Warnings
The information disclosed herein includes proprietary
rights of the manufacturer. Neither this document nor
the information disclosed herein shall be reproduced
or transferred to other documents, used or disclosed
to others for manufacturing purposes, or for any other
purposes, except as specifi cally authorized in writing by
the manufacturer. If this manual is supplied in connection
with the sale or delivery of manufacturer’s equipment, it is
to be used solely for maintenance, repair or installation of
such equipment.
You MUST read and fully understand the following
information pertaining to the proper use and limitations of
your PressCam 8:
• The PressCam 8 MUST be installed by qualifi ed
personnel only.
• The PressCam 8 MUST NOT be used on full
revolution presses or any machine that cannot be
commanded to stop at any time.
• The press on which the PressCam 8 is installed
MUST meet OSHA 1910.217 regulations which
include inspection and maintenance procedures that
MUST be followed to meet these regulations. And
is highly recommended that the press meet current
ANSI B11.1-1988 standards. The manufacturer
WILL NOT take responsibility for improperly
maintained machinery.
• The PressCam 8 MUST be checked out before
put into use, follow this manual for the proper
procedures.
• The PressCam 8 SHALL NOT be modified or
repaired except by qualifi ed personnel and/or upon
authorization of the manufacturer. Never operate
machinery that is not in full working order.
• Make sure that all maintenance people, machine
operators, die-setters, foremen, and supervisors
have read and understand this manual.
• All procedures in this manual MUST be followed.
The manufacturer WILL NOT take responsibility for
operation if all procedures and warnings listed in all
manuals are not followed.
Warranty
Manufacturer warrants that this product will be free from
defects in material and workmanship for a period of two
years from the date of shipment thereof. Within the
warranty period, manufacturer will repair or replace such
products which are returned with shipping charges prepaid
and which will be disclosed as defective upon examination
by the manufacturer. This warranty will not apply to any
product which will have been subject to misuse, negligence,
accident, restriction, and use not in accordance with
manufacturer’s instructions or which will have been altered
or repaired by person’s other than the authorized agent or
employees of the manufacturer.
Disclaimer
The provisions of the paragraph “WARRANTY” are the
sole obligations of the manufacturer and exclude all other
warranties of merchantability, expressed or implied.
Further, there are not warranties which extend beyond the
above warranty.
Limitation of Liability
In the event of any claim for breach of any obligations
of manufacturer under any order, whether expressed
or implied, and particularly in the event of any claim of
a breach of the warranty or warranties contained in the
paragraph “WARRANTY” or of any other warranties,
expressed or implied which might despite the paragraph
entitled “DISCLAIMER,” be determined to be incorporated
in any order, the company shall under no circumstances
be liable for any consequential or special damages, either
in law or in equity, or for losses or expenses or claims for
the same arising from the use of, or inability to use, the
products of the manufacturer for any purpose whatsoever.
This equipment has been designed to the very highest
performance and safety standards known to the current
technological state of the art. However, the installation,
usage, suitability, and fi tness of our equipment for any
purpose, known or unknown, is interdependent upon
the performance of other equipment not manufactured,
installed, or secured or maintained by the manufacturer.
We WILL NOT and DO NOT accept responsibility for any
overall system performance when factors, such as these,
are beyond our control.
WARNING: The entire machine safety system must
be tested at the start of every shift. Machine testing
should include: (1) proper machine operation and
stopping capability; and (2) verifi cation of proper
installation and settings of all point of operation
guards and devices before the operation is released
for production.
FILL THIS INFORMATION OUT IMMEDIATELY
PURCHASE DATE: ______________________
PURCHASED FROM: ____________________
MODEL NO.: ___________________________
SERIAL NO.: ___________________________
OPTIONS: _____________________________
SOFTWARE REVISION NO.: ______________
This information will be needed in the event
you need assistance
To Next Page
Loading...