Raymarine p70r User Manual (English)

Other manuals for Raymarine p70r

Installation & Operation Instructions122 pages

Installation And Operation Instructions104 pages

Quick Reference12 pages

Installation Guide4 pages

Installation Instructions80 pages

Questions and Answers:

T
Tommy YuAug 18, 2025
What to do if instrument data is unavailable on Raymarine Marine Equipment displays?
- R
  randy68Aug 18, 2025
  If instrument, engine, or other system data isn't showing on any Raymarine Marine Equipment displays, start by checking the data bus wiring and connections to ensure they are properly connected. Also, verify the overall integrity of the data bus wiring. Confirm that the source of the missing data, such as an ST70 instrument or engine interface, is operational. Check the power to the SeaTalk bus. If these steps don't resolve the issue, there may be a software mismatch and you should contact Raymarine technical support.
A
Alexander JonesAug 20, 2025
Why my Raymarine Marine Equipment system does not start up?
- B
  Brandon EvansAug 20, 2025
  If your Raymarine Marine Equipment system or part of it fails to start, begin by inspecting the relevant fuses and breakers. Ensure the power supply cable is in good condition, with tight, corrosion-free connections. Verify that the power source provides the correct voltage and sufficient current.
C
Craig FosterAug 22, 2025
What to do if Raymarine Marine Equipment display behaves erratically?
- A
  Anna OrozcoAug 23, 2025
  If your Raymarine Marine Equipment display is behaving erratically with frequent resets or system crashes, check the fuses and breakers. Ensure the power supply cable is sound, with tight and corrosion-free connections, and that the power source provides the correct voltage and current. Make sure the front bezel is correctly fitted and all buttons operate freely. If problems persist, go to www.raymarine.com and click on support for the latest software downloads. As a last resort, perform a factory reset via Menu > System Setup > Settings and Data Reset, but remember this will erase stored settings and data; save important data to a CF card beforehand.
T
Troy SantiagoAug 26, 2025
What to do if my Raymarine Marine Equipment display behaves erratically?
- K
  Kathleen CarrAug 26, 2025
  If your Raymarine Marine Equipment display behaves erratically with frequent unexpected resets or system crashes, first check the relevant fuses and breakers. If the issue persists, a factory reset may be needed. Be aware that this will erase all settings and data stored on the product, so save any important data to a memory card beforehand.
M
Michelle PerezAug 27, 2025
How to fix a Raymarine Marine Equipment that won't turn on?
- J
  joann64Aug 27, 2025
  If your Raymarine Marine Equipment product does not turn on or keeps turning off, begin by checking the fuses, breakers, and their connections, replacing any that are blown or tripped. If fuses continue to blow, inspect for cable damage, broken connector pins, or incorrect wiring. Also, verify the power cable is securely inserted, check for damage or corrosion, and flex the cable to see if it causes a reboot. Ensure the vessel's battery voltage is adequate, and the terminals and cables are clean, secure, and free from corrosion. Finally, use a multi-meter to check for high voltage drop across connectors and fuses.
M
Micheal SchwartzAug 30, 2025
What to do if my Raymarine Marine Equipment won't boot up?
- J
  jessica91Aug 30, 2025
  If your Raymarine Marine Equipment product will not boot up and is stuck in a reboot loop, check the power supply and connections as you would if the product wouldn't turn on at all. In case of software corruption, try re-flashing the latest software from the Raymarine website. As a last resort, perform a ‘Power on Reset’. Note: This will delete all settings, presets, and user data, reverting the unit to factory defaults.
A
Ashley SmithSep 2, 2025
Why is instrument data missing on all my Raymarine Marine Equipment displays?
- A
  Alison SmithSep 2, 2025
  If instrument, engine, or other system data is unavailable on all Raymarine Marine Equipment displays, verify the data bus (e.g., SeaTalkng) wiring and connections, ensuring the overall integrity of the wiring. Check the source of the missing data, such as the ST70 instrument or engine interface, to ensure it is operating correctly. Also, check the power to the SeaTalk bus. If a software mismatch is suspected, contact Raymarine technical support.
T
thurstSep 4, 2025
How to troubleshoot missing data on some Raymarine Marine Equipment displays?
- J
  Jason MooreSep 4, 2025
  If instrument or other system data is missing from some Raymarine Marine Equipment displays but not all, check that all required equipment is connected to the SeaTalkhs switch. Verify the status of the SeaTalkhs Switch and inspect SeaTalkhs cables for damage. If the issue persists, contact Raymarine technical support as there may be a software mismatch.
J
joneskathleenSep 6, 2025
Why is instrument data missing from all my Raymarine Marine Equipment displays?
- M
  Melissa RivasSep 6, 2025
  If instrument, engine, or other system data is unavailable at all Raymarine Marine Equipment displays, check the data bus wiring and connections. Also, check the data source (e.g., instrument display or engine interface) to ensure it is operating correctly.
M
Mark TorresSep 9, 2025
Why is instrument data missing from some of my Raymarine Marine Equipment displays?
- M
  Michael MorrisSep 9, 2025
  If instrument or other system data is missing from some, but not all, Raymarine Marine Equipment displays, check that all required equipment is connected to the network.

Raymarine p70r Specifications

General

Display Type	LCD
Resolution	320 x 240 pixels
Waterproof Rating	IPX6
Connectivity	SeaTalkng
Operating Temperature	-15°C to +55°C
Type	Autopilot Control Unit
Compatibility	Raymarine Autopilot Systems
Display Size	3.5 inches
Operating Voltage	10-32V DC