What to do if LAST flashing or dashes displayed continuously on Raymarine i50 Depth?
If 'LAST' is flashing or dashes are continuously displayed on your Raymarine Marine Equipment (depth greater than 3 feet), check the condition of the transducer cable(s) and the security of the connections.
Why LAST flashes when underway on Raymarine Marine Equipment?
If 'LAST' flashes when your Raymarine Marine Equipment is underway, it may be due to aerated water from vessel wakes or propeller wash. Ensure the reading stabilizes when clear of disturbed water.
What to do if my Raymarine i50 Depth display behaves erratically?
If your Raymarine Marine Equipment display behaves erratically, with frequent unexpected resets or system crashes, start by checking the relevant fuses and breakers. Also, check the power supply cable to ensure it's sound, with tight and corrosion-free connections. Verify that the power source provides the correct voltage and sufficient current. If the problem persists, go to www.raymarine.com and click on support for the latest software downloads. As a last resort, perform a factory reset, but remember this will erase all your settings and data; save important data to a memory card beforehand.
What to do if a group of SeaTalk/SeaTalkng Raymarine Marine Equipment units not working?
If a group of SeaTalk/SeaTalkng Raymarine Marine Equipment units aren't working, check the security of SeaTalk/SeaTalkng connectors between the functioning and non-functioning units. Also, check the condition of the SeaTalk/SeaTalkng cable between these units.
How to fix a blank display on Raymarine i50 Depth?
If your Raymarine Marine Equipment display is blank, check the fuse or circuit breaker and the power supply. Also, check the SeaTalk/SeaTalkng cabling and connector security.
General| Brand | Raymarine |
|---|---|
| Model | i50 Depth |
| Category | Marine Equipment |
| Language | English |
Details for obtaining enhanced warranty benefits through certified installation.
Disclaimer regarding water intrusion and potential equipment failure from high-pressure washing.
Information on product warranty, compatibility, and liability for damages or injuries.
Guidelines for proper installation to ensure optimal Electromagnetic Compatibility performance.
Importance and correct usage of suppression ferrites for EMC performance.
Requirement for suppression ferrites on non-Raymarine cables.
Statement of compliance with essential requirements of EMC directive 2004/108/EC.
Instructions for disposing of the product in accordance with the WEEE Directive.
Guidance on registering product ownership online for full warranty benefits.
Intended use for leisure boats and workboats, not IMO/SOLAS carriage regulations.
Information on document accuracy, potential inaccuracies, and product improvement changes.
Details about the document, its purpose, and applicable Raymarine products.
List and illustrations of components included in the product package.
General features and capabilities of the i50 instrument display range.
A step-by-step guide for planning and executing the installation process.
List of depth and speed transducers compatible with i50 instrument displays.
Diagrams illustrating basic and extended SeaTalkng system configurations.
Explanation of SeaTalkng, NMEA 2000, and SeaTalk protocols for system connectivity.
List of essential tools needed for the installation of the instrument.
Factors to consider when choosing a suitable mounting location for the display unit.
Detailed measurements and specifications of the i50 instrument unit.
Guidelines for choosing optimal mounting positions for speed and depth transducers.
Best practices for cable types, routing, strain relief, and shielding.
Instructions for connecting the 12V DC power supply to the SeaTalkng network.
Procedure for connecting SeaTalkng cables to the unit's rear connectors.
Details on connecting depth and speed transducers using spade connectors.
Connecting transducers via the iTC-5 converter for data distribution.
Connecting to an existing SeaTalk system using a SeaTalk to SeaTalkng adaptor.
Methods for connecting the unit to SeaTalkng or existing NMEA2000 backbones.
Instructions for surface mounting the i50 instrument display unit.
Procedure for safely removing and refitting the front bezel of the unit.
Overview of the i50 Depth instrument's functions and data display capabilities.
Description of the buttons and their functions for operating the i50 Depth unit.
Procedures for powering the unit on and off, including countdown timers.
Setting the instrument status as Master or Repeater for system data distribution.
Overview of user, intermediate, and dealer calibration procedures for optimal performance.
Steps for setting depth units and applying depth offsets in user calibration.
Checking software version and setting instrument status (Master/Repeater).
Advanced settings including user access, response delay, and factory reset.
Navigating through current depth, minimum, and maximum depth display pages.
How to view the applied waterline or keel offset value for depth readings.
Setting and managing shallow/deep depth and anchor alarms for the i50 Depth unit.
Adjusting backlight and contrast levels, and configuring group illumination.
Overview of the i50 Speed instrument's functions and data display capabilities.
Description of the buttons and their functions for operating the i50 Speed unit.
Procedures for powering the unit on and off, including countdown timers.
Setting the instrument status as Master or Repeater for system data distribution.
Overview of user, intermediate, and dealer calibration procedures for optimal performance.
Settings for speed units, resolution, log units, temp units, speed offset, timer buzzer.
Checking software version and performing speed run calibration for accurate readings.
Advanced settings: user access, response delay, boat show mode, and factory reset.
Navigating through current, maximum, average speed, VMG, and SOG pages.
Accessing and viewing log, trip, and water temperature data.
Operating race start timers and stopwatch, including buzzer settings.
Adjusting backlight and contrast levels, and configuring group illumination.
Overview of the i50 Tridata instrument's functions and data display capabilities.
Description of buttons for operating the i50 Tridata unit and navigating its display.
Procedures for powering the unit on and off, including countdown timers.
Setting instrument status to Master or Repeater for data distribution.
Overview of user, intermediate, and dealer calibration procedures for optimal performance.
Settings for depth, speed, log units, temp units, speed offset, and timer buzzer.
Checking software version and performing speed run calibration for accurate readings.
Settings for user access, speed/depth response, SOG source, boat show mode, reset.
Navigating depth pages: current, shallow/deep depth and anchor alarms.
Navigating speed pages: current, max, average speed, VMG.
Accessing trip, log, water temperature, and timer data displays.
Operating race start timers and stopwatch, including buzzer settings.
Setting and managing shallow/deep depth and anchor alarms for the i50 Tridata unit.
Adjusting backlight and contrast levels, and configuring group illumination.
Information on product servicing, repairs, and authorized dealer services.
Explanation of condensation on the unit's window and how it clears.
Recommendations for regular checks to ensure reliable equipment operation.
Best practices for cleaning the product, avoiding abrasive materials.
Procedure for cleaning the sealed display unit case.
Procedure for cleaning the screen to maintain water repellency and prevent glare.
Introduction to troubleshooting common marine electronics installation problems.
Diagnosing and resolving faults related to displays, data transfer, and transducer issues.
Solutions for problems encountered when the system or parts of it do not start up.
Addressing erratic display behavior, resets, system crashes, and software mismatches.
Information on contacting Raymarine for customer support via web, phone, and email.
Steps to identify the software version of the i50 instrument display.
Detailed specifications including voltage, power, current, environmental, and connections.
List of available spare parts for i50 instrument displays.
Details on SeaTalkng cables, connectors, and accessory kits.
Information on available converters, including SeaTalk to SeaTalkng.
List of supported NMEA 2000 Parameter Group Number (PGN) sentences.
To Next Page