EasyManua.ls Logo

Raymarine SmartPilot SPX-10 User Manual

Raymarine SmartPilot SPX-10
50 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Page #1 background imageLoading...
Page #1 background image
SPXSmartPilotinstallationinstructions
Question and Answer IconNeed help?

Do you have a question about the Raymarine SmartPilot SPX-10 and is the answer not in the manual?

Raymarine SmartPilot SPX-10 Specifications

General IconGeneral
Compass TypeFluxgate
SeaTalk/SeaTalkngYes
NMEA0183Yes
Seatalk CompatibleYes
ControlYes
Power Supply12/24V DC
Max Boat Length10m (33ft)
Maximum Boat Length10m (33ft)
Compass SensorYes
Course ComputerYes
CompatibilityRaymarine
NMEA 2000 CompatibleYes
HumidityUp to 95%

Summary

Chapter 1: Introduction

Handbook information

Describes the installation of SPX course computers as part of a SmartPilot autopilot system.

SPX handbooks

Lists related Raymarine SPX and ST70 Pilot Controller documentation with part numbers.

Important information

Product installation and operation warnings

Critical warnings regarding product installation, operation, potential ignition sources, and power supply safety.

Service and maintenance cautions

Cautions regarding user serviceable components and power supply protection for the autopilot system.

Certified installation

EMC installation guidelines

Guidelines for minimizing electromagnetic interference for optimal system performance and compliance.

Suppression ferrites

Information on the use and importance of suppression ferrites for EMC performance.

Product disposal

Guidance on proper disposal of the product in accordance with the WEEE Directive.

Technical accuracy

Disclaimer regarding the accuracy of information and potential product improvements.

Chapter 2: Planning the installation

Installation checklist

Lists activities for planning and executing the autopilot system installation.

Inboard autopilot system

Details components of a typical inboard autopilot system and their functions.

SeaTalkng autopilot system

Explains how the autopilot connects as part of a SeaTalkng network of marine electronics.

SeaTalk autopilot system

Details how the autopilot connects as part of a SeaTalk network of marine electronics.

Parts supplied

Lists the components included in the SPX core pack.

Required additional components

Lists necessary components to complete the autopilot system installation.

Drive units

Describes the main categories of drive units compatible with the course computer and their types.

Chapter 3: Cables and connections

General cabling guidance

Provides guidelines on cable types, length, routing, strain relief, circuit isolation, and shielding.

SPX-10 / SPX-30 connections overview

Illustrates and describes the connection points for SPX-10 and SPX-30 course computers.

SPX-SOL connections overview

Illustrates and describes the connection points for the SPX-SOL course computer.

Power and drive cables

Details power and drive cable selection based on drive type, voltage, and length.

Fuses and circuit protection

Specifies fuse and circuit breaker ratings required for different drive units and system power.

Grounding

Outlines grounding requirements for Raymarine equipment, including bonded and RF ground systems.

SPX to SeaTalkng connection

Explains how to connect the SPX course computer to a SeaTalkng network.

SeaTalk connection

Describes how to connect the SPX course computer to a SeaTalk network.

NMEA 0183 connection

Details the NMEA 0183 input/output compatibility and connection for the SPX autopilot.

Compass connection

Illustrates and describes the connection of the fluxgate compass to the course computer.

Rudder reference connection

Shows how to connect the rudder reference sensor to the course computer.

Sleep switch connection

Explains the connection for a sleep switch to disable autopilot operation.

Chapter 4: Installation

Location requirements for SPX course computers

Specifies the ideal physical location requirements for installing SPX course computers.

Installing the SPX course computer

Provides a step-by-step procedure for mounting and connecting the SPX course computer.

Initial checks for the autopilot installation

Lists essential checks to perform after installation and before commissioning the autopilot system.

Chapter 5: Maintenance and support

Service and maintenance

States that the product has no user serviceable components and directs users to authorized dealers.

Cleaning

Provides instructions on how to safely clean the autopilot unit using specific cleaning agents.

Raymarine customer support

Offers information on how to contact Raymarine customer support via web, telephone, and email.

Appendix A Technical specification

Technical Specification Details

Details on nominal supply voltage, operating voltage, fuses, power outputs, consumption, and gyro.

Environmental and Installation Conditions

Specifies operating and storage temperatures, humidity limits, water protection, and installation environment factors.

Dimensions and Weight

Provides physical dimensions and weight for the SPX course computer models.

Data Connections and Other Interfaces

Lists data connections like NMEA 0183, SeaTalkng, SeaTalk, and other interfaces.

Appendix B NMEA 0183 sentences

NMEA 0183 Receive Sentences

Lists NMEA 0183 sentences that the SPX autopilot can receive and their meanings.

NMEA 0183 Transmit Sentences

Lists NMEA 0183 sentences that the SPX autopilot can transmit and their meanings.

Appendix C SeaTalkng accessories

SeaTalkng Cables and Accessories

Lists SeaTalkng cables and accessories with part numbers and notes for compatible products.

Appendix D SeaTalk accessories

SeaTalk Cables and Accessories

Lists SeaTalk cables and accessories with part numbers and notes for compatible products.

Related product manuals