What should I do if my Riello UPS doesn't switch on and displays codes A06 or A08?
If your Riello UPS fails to power on and shows error codes A06 or A08, it indicates that the UPS temperature is below 0°C. Ensure the UPS is in an environment where the temperature is above the minimum threshold of 0°C.
What to do if the Riello UPS buzzer sounds continuously and shows codes F04, L04?
If your Riello UPS is beeping continuously and displaying one of the listed error codes, it indicates that the temperature of the dissipators inside the UPS is too high. Ensure the ambient temperature around the UPS does not exceed 40°C.
What to do if the Riello UPS buzzer sounds continuously and shows codes F53, L53?
If your Riello UPS is beeping continuously and displaying one of the listed error codes, it means a fault has been detected on one or more connected devices. Disconnect all devices and reconnect them individually to identify the faulty one.
General| Model | SDL 8000 |
|---|---|
| Apparent Power | 8000 VA |
| Active Power | 7200 W |
| Output Frequency | 50/60 Hz |
| Battery Type | Sealed lead-acid |
| Operating Temperature | 0 - 40 °C |
| Output Waveform | Sinusoidal |
| Communication Interface | RS232, USB |
This part of the manual contains precautions that must be adhered to strictly since they regard SAFETY.
Details the company's commitment to environmental aspects and the materials used in packaging.
Information on treating and disposing of toxic and hazardous waste materials from the UPS.
Illustrates the two different installation versions of the Sentinel Dual UPS product.
Diagrams showing the front and rear views of the UPS unit with key components labeled.
Diagrams showing the front and rear views of the battery box with key components labeled.
Details the LCD display elements, buttons, and indicators on the UPS front panel.
Lists the items typically found in the UPS and battery box packaging for verification.
Describes the operations for preparing the UPS and battery box for tower configuration.
Details the sequence of operations to convert the UPS and battery box into a rack version.
Lists essential points to ensure before connecting the UPS to the battery box.
Instructions on how to connect the UPS to the battery box using the provided cable and fuses.
Details essential safety and procedural steps for connecting the UPS to mains and load.
Step-by-step guide for connecting the 8-10kVA single phase UPS to power sources and load.
Instructions for connecting 8-10kVA and 6.5kVA three-phase UPS models to power.
Steps to configure the bypass remote maintenance control externally for the UPS.
Guides through the initial steps to power on and verify the UPS after installation.
Instructions on how to start the UPS when connected to the mains power supply.
Steps to initiate the UPS operation directly from the battery power.
Procedures for safely turning off the UPS, including stand-by and complete shutdown.
Explains the meaning of various icons, statuses, and indicators shown on the UPS LCD display.
Details how to view different UPS measurements (voltage, frequency, load) on the display.
Describes the settable parameters on the UPS display and how to change them.
Explains different UPS operating modes like ON LINE, ECO, SMART ACTIVE, and STAND-BY OFF.
Details the function and connection of the remote emergency power off switch.
Explains the function of the programmable output socket for load disconnection.
Provides a table of configurable UPS parameters and their possible settings.
Lists advanced settings for input frequency tolerance, bypass voltage, and ECO mode sensitivity.
Describes the RS232, USB connectors, and expansion slots for communication.
Details the monitoring, control, and configuration software for the UPS.
A table listing common UPS issues and their corresponding solutions.
Lists and explains fault and alarm codes indicated by the UPS.
Presents technical specifications for single/single-phase UPS models.
Presents technical specifications for three/single-phase UPS models.
Provides technical specifications for the UPS battery box models.
Details how the UPS responds to different overload conditions in bypass and inverter modes.
To Next Page