Need help?Do you have a question about the Rigol DHO924S and is the answer not in the manual?
General| Bandwidth | 250 MHz |
|---|---|
| Channels | 4 |
| Vertical Resolution | 12-bit |
| Waveform Capture Rate | 1, 000, 000 wfms/s |
| Vertical Sensitivity | 1 mV/div to 10 V/div |
| FFT | Yes |
| Timebase Accuracy | ±5 ppm |
| Display | 10.1-inch capacitive touch screen |
| Trigger Types | Edge, Pulse, Slope, Video, Pattern, Duration, TimeOut, Runt, Window |
| Serial Bus Triggering and Decoding | RS232/UART, I2C, SPI, CAN, LIN |
| Interfaces | USB Host, USB Device, LAN, HDMI, AUX |
| Input Impedance | 1 MΩ ± 1% |
| Maximum Input Voltage | 400 V (DC + AC peak) |
| Operating Temperature | 0°C to 40°C |
Provides essential safety precautions for instrument operation to prevent injury or damage.
Defines measurement categories and warnings for safe usage within specified limits.
Specifies operating temperature, humidity, altitude, and protection levels.
Details compliance with WEEE directive and recommendations for product recycling.
Explains conventions for keys, menus, operations, connectors, and knobs used in the manual.
Guides the user through inspecting packaging, the instrument, and accessories.
Provides visual information and physical dimensions of the instrument.
Covers initial setup steps like adjusting legs and connecting to power.
Introduces the instrument's appearance, panels, and user interface.
Details the components and functionality of the instrument's front panel.
Explains how to use touch screen gestures like Tap, Drag, and Pinch&Stretch.
Describes methods for setting parameters using knobs and the touch screen.
Instructions on how to turn analog channels on or off.
Explains how to adjust the vertical scale (Volts/division) for waveform amplitude.
Details how to adjust the vertical offset to position the waveform vertically.
Describes how to select coupling modes (DC, AC, GND) to filter signals.
Explains how to set the horizontal time base (Time/division) for waveform scaling.
Guides on adjusting the horizontal position of the waveform relative to the display center.
Describes how to use zoom mode to horizontally expand waveform details.
Explains acquisition modes like Normal, Average, Peak, and UltraAcquire.
Details the sample rate and its impact on waveform display.
Describes memory depth and its relation to sample rate and horizontal time base.
Specifies how to select analog or digital channels as trigger sources.
Explains how to adjust the trigger level for stable waveform capture.
Describes trigger modes: Auto, Normal, and Single.
Lists and describes available trigger types.
Details the functionality of the AUX OUT connector for trigger signals.
Explains how to perform addition, subtraction, multiplication, and division of waveforms.
Describes how to use Fast Fourier Transform for frequency spectrum analysis.
Explains how to perform logic operations (AND, OR, XOR, NOT) on waveforms.
Enables automatic configuration for optimal waveform display and measurement.
Allows quick measurements of waveform parameters.
Explains how to use cursors for measuring X and Y axis values.
Details the built-in DVM for 4-digit voltage measurements.
Describes the frequency counter for frequency, period, and edge event measurements.
Instructions for enabling or disabling digital channels.
Explains how to set threshold levels for digital channels.
Allows setting user-defined labels for digital channels.
Enables or disables the histogram analysis function.
Details the statistical data results displayed in the histogram analysis.
Guides on outputting basic waveforms like Sine, Square, Ramp, DC, Noise.
Explains amplitude (AM), frequency (FM), and phase (PM) modulation.
Covers enabling/disabling Bode plot, operation control, source, sweep, and display types.
Details how to save and load Bode plot test data.
Instructions to access and enable the reference waveform function.
Explains how to specify channels, save, and clear reference waveforms.
Covers saving and loading reference waveforms to/from memory.
Enables or disables the pass/fail test function.
Guides on defining and managing pass/fail test masks.
Configures output events, polarity, pulse width, and error actions.
Instructions to start, stop, save, and load pass/fail test operations.
Explains parallel bus decoding, clock setting, and bus configuration.
Details RS232 serial bus decoding, source setting, and data package configuration.
Covers I2C serial bus decoding, source setting, and display parameters.
Explains SPI bus decoding, setting source, mode, and data.
Describes LIN signal decoding, signal configuration, and display settings.
Details CAN signal decoding and signal configuration.
Describes how to add multiple display windows like XY and Math.
Covers enabling waveform recording and setting recording parameters.
Details parameters for waveform recording: Interval, Frames, Max Frames, Beeper.
Explains options for playing back recorded waveforms: Play Mode, Sequence, Interval.
Allows finding and marking events like edges and pulses in waveforms.
Provides functions to navigate time, search events, and frame segments.
Sets the display mode, e.g., Vector, for waveform visualization.
Adjusts persistence time to view waveform changes and glitches.
Adjusts the brightness of the displayed waveforms.
Configures the display grid appearance (FULL, HALF, NONE).
Covers grid brightness and window transparency settings.
Enables or disables the waveform freeze function.
Accesses the menu for saving, loading, and upgrading instrument data.
Guides on saving image, waveform, or setup files.
Details saving waveform data and format to memory or USB.
Explains how to perform local and online firmware upgrades.
Configures network parameters like IP address, MAC, and VISA address.
Covers language selection and system configuration recall.
Provides information about the instrument's model, firmware, and software versions.
Initiates the self-calibration program for optimal measurement accuracy.
Allows configuration of quick action keys on the front panel.
Control via SCPI commands for custom programming.
Control using PC software like RIGOL Ultra Sigma.
Instrument control via a web browser interface over the network.
Guides on connecting and controlling the instrument via USB.
Guides on connecting and controlling the instrument via LAN.
Lists available accessories and their order numbers.
Details the product warranty terms and conditions.
Provides a table of the instrument's default factory settings.
To Next Page
