Roger Technology H70/105AC - Page 52

EN
52
CONTACT DESCRIPTION
14(FT2) 13(COM)
Input (N.C.) for connecting photocells FT2ƼK
The photocells FT2 EVIGSRƼKYVIHF]HIJEYPX[MXLXLIJSPPS[MRKWIXXMRKW
–  (YVMRK KEXISTIRMRK the gate stops as long as the photocell is obstructed. The gate
resumed opening when the photocell is cleared.
–  . Movement is reversed if the photocell FT2 is triggered during gate closure.
–  . -JXLITLSXSGIPPMWSFWXVYGXIHXLIKEXIGERRSXSTIR
-JXLITLSXSGIPPWEVIRSXMRWXEPPIHNYQTIVXLIXIVQMREPW14(FT2) - 13(COM) or set the parameters
  and  .
15(FT1) 13(COM)
Input (N.C.) for connecting photocells FT1ƼK
The photocells FT1 EVIGSRƼKYVIHF]HIJEYPX[MXLXLIJSPPS[MRKWIXXMRKW
–  . Photocell triggers only during gate closure. Photocell is ignored during gate opening.
–  . Movement is reversed if the photocell FT1 is triggered during gate closure.
–  . -JXLITLSXSGIPPMWSFWXVYGXIHXLIKEXIGERRSXSTIR
-JXLITLSXSGIPPWEVIRSXMRWXEPPIHNYQTIVXLIXIVQMREPW15(FT1) - 13(COM) or set the parameters
  and  .
16(COS2) 13(COM)
Input (NC or 8 kOhm) for connecting sensing edge COS2 ƼK.
8LIWIRWMRKIHKIMWGSRƼKYVIHF]HIJEYPX[MXLXLIJSPPS[MRKWIXXMRKW
–  . The sensing edge COS2 (NC contact) is disabled.
-JXLIWIRWMRKIHKIMWRSXMRWXEPPIHNYQTIVXLIXIVQMREPW16(COS2) - 13(COM) or set the parameter
 .
17(COS1) 13(COM)
Input (NC or 8 kOhm) for connecting sensing edge COS1 ƼK
8LIWIRWMRKIHKIMWGSRƼKYVIHF]HIJEYPX[MXLXLIJSPPS[MRKWIXXMRKW
–  . The sensing edge COS1 (NC contact) is disabled.
-JXLIWIRWMRKIHKIMWRSXMRWXEPPIHNYQTIVXLIXIVQMREPW17(COS1) - 13(COM) or set the parameter
 .
18(ST) 13(COM)
STOP command input (NC). The current manoeuvre is arrested if the safety contact opens. N.B.: the
controller is supplied with this contact already jumpered by ROGER TECHNOLOGY.
19(PP) 13(COM)
Step by step mode command input (N.O.).
The function of the control is determined by parameter $.
20 21(ANT)
Antenna connector for slot-in radio receiver board.
9WI6+MJERI\XIVREPERXIRREMWYWIHQE\MQYQVIGSQQIRHIHPIRKXLQ
N.B.HSRSXQEOINSMRXWMRGEFPI
22(ORO) 26(COM)
Clock timer contact input (N.O.).
;LIRXLIGPSGOJYRGXMSRMWEGXMZIXLIKEXISTIRWERHVIQEMRWSTIR
%XXLIIRHSJXLITVSKVEQQIHXMQIWIX[MXLXLII\XIVREPHIZMGIGPSGOXLIKEXIGPSWIW
23(PED) 26(COM)
Partial open control signal input (N.O.).
Set by default to 30% of completely open position.
24(CH) 26(COM)
Close command input (N.O.).
25(AP) 26(COM)
Open control signal input (N.O.).
H70/104AC
SB
'SRRIGXSV2'JSVGSRRIGXMRKVIPIEWIGSRXEGX-JXLIQSXSVVIPIEWILERHPIMWSTIRIHXLIKEXI
stops and no command signals are accepted.
3RGIXLIVIPIEWILERHPIMWGPSWIHEKEMRMJXLIKEXIMWMRERMRXIVQIHMEXITSWMXMSRXLIGSRXVSPPIVYRMX
initiates the position recovery procedure (see chapter 18).
N.B.6IEH][MVIHMRJEGXSV]F]63+)68)',2303+=
FC
Connector (N.C. contacts) for connecting mechanical limit switch (see ƼKYVI - detail A) or mag-
netic limit switch (see ƼKYVI - detail B). The gate stops when the limit switch is activated.
N.B.6IEH][MVIHMRJEGXSV]F]63+)68)',2303+=
ENC
Connector for connecting to encoder installed on motor.
WARNING! Always disconnect from electrical power before disconnecting or connecting the
encoder cable.
N.B.6IEH][MVIHMRJEGXSV]F]63+)68)',2303+=