Roland V-Synth GT - Main Features; Sound creation power driven by dual-core technology; AP-Synthesis enables a new dimension of performance expression; A powerful user interface that’s easier to use than ever

16
List of Added Reverb
14: FG ROOM
This is a reverb used in the Fantom-G.
Simulates the reverberation of a room.
15: FG HALL
This is a reverb used in the Fantom-G.
Simulates the reverberation of a concert hall.
16: FG PLATE
This is a reverb used in the Fantom-G.
Simulates plate reverberation (a reverb unit that uses the
vibration of a metallic plate).
17: FG STUDIO
This is a reverb used in the Fantom-G.
Simulates the reverberation of a studio.
18: FG CHURCH
This is a reverb used in the Fantom-G.
Simulates the reverberation of a church.
Parameter
Value Description
Pre Delay 0–127
Adjusts the delay time from the direct sound
until the reverb sound is heard.
Time 0.1–3.0 sec Time length of reverberation
Low Damp Freq 20–1000 Hz
Adjusts the frequency below which the low-
frequency content of the reverb sound will be
reduced, or “damped.”
Low Damp 1–100%
Adjusts the amount of damping applied to the
frequency range selected with LF Damp. With a
setting of “100%,” there will be no reduction of
the reverb’s low-frequency content.
Hi Damp Freq 1000–10000 Hz
Adjusts the frequency above which the high-
frequency content of the reverb sound will be
reduced, or “damped.”
High Damp 1–100%
Adjusts the amount of damping applied to the
frequency range selected with HF Damp. With a
setting of “100%,” there will be no reduction of
the reverb’s high-frequency content.
High Cut 1000–10000 Hz
Adjusts the frequency above which the high-
frequency content of the reverb will be
reduced.
Parameter
Value Description
Pre Delay 0–127
Adjusts the delay time from the direct sound
until the reverb sound is heard.
Time 0.1–6.0 sec Time length of reverberation
Low Damp Freq 20–1000 Hz
Adjusts the frequency below which the low-
frequency content of the reverb sound will be
reduced, or “damped.”
Low Damp 1–100%
Adjusts the amount of damping applied to the
frequency range selected with LF Damp. With a
setting of “100%,” there will be no reduction of
the reverb’s low-frequency content.
Hi Damp Freq 1000–10000 Hz
Adjusts the frequency above which the high-
frequency content of the reverb sound will be
reduced, or “damped.”
High Damp 1–100%
Adjusts the amount of damping applied to the
frequency range selected with HF Damp. With a
setting of “100%,” there will be no reduction of
the reverb’s high-frequency content.
High Cut 1000–10000 Hz
Adjusts the frequency above which the high-
frequency content of the reverb will be
reduced.
Parameter
Value Description
Pre Delay 0–127
Adjusts the delay time from the direct sound
until the reverb sound is heard.
Time 0.1–6.0 sec Time length of reverberation
Low Damp Freq 20–1000 Hz
Adjusts the frequency below which the low-
frequency content of the reverb sound will be
reduced, or “damped.”
Low Damp 1–100%
Adjusts the amount of damping applied to the
frequency range selected with LF Damp. With a
setting of “100%,” there will be no reduction of
the reverb’s low-frequency content.
Hi Damp Freq 1000–10000 Hz
Adjusts the frequency above which the high-
frequency content of the reverb sound will be
reduced, or “damped.”
High Damp 1–100%
Adjusts the amount of damping applied to the
frequency range selected with HF Damp. With a
setting of “100%,” there will be no reduction of
the reverb’s high-frequency content.
High Cut 1000–10000 Hz
Adjusts the frequency above which the high-
frequency content of the reverb will be
reduced.
Parameter
Value Description
Pre Delay 0–127
Adjusts the delay time from the direct sound
until the reverb sound is heard.
Time 0.1–3.0 sec Time length of reverberation
Low Damp Freq 20–1000 Hz
Adjusts the frequency below which the low-
frequency content of the reverb sound will be
reduced, or “damped.”
Low Damp 1–100%
Adjusts the amount of damping applied to the
frequency range selected with LF Damp. With a
setting of “100%,” there will be no reduction of
the reverb’s low-frequency content.
Hi Damp Freq 1000–10000 Hz
Adjusts the frequency above which the high-
frequency content of the reverb sound will be
reduced, or “damped.”
High Damp 1–100%
Adjusts the amount of damping applied to the
frequency range selected with HF Damp. With a
setting of “100%,” there will be no reduction of
the reverb’s high-frequency content.
High Cut 1000–10000 Hz
Adjusts the frequency above which the high-
frequency content of the reverb will be
reduced.
Parameter
Value Description
Pre Delay 0–127
Adjusts the delay time from the direct sound
until the reverb sound is heard.
Time 0.1–6.0 sec Time length of reverberation
Low Damp Freq 20–1000 Hz
Adjusts the frequency below which the low-
frequency content of the reverb sound will be
reduced, or “damped.”
Low Damp 1–100%
Adjusts the amount of damping applied to the
frequency range selected with LF Damp. With a
setting of “100%,” there will be no reduction of
the reverb’s low-frequency content.
Hi Damp Freq 1000–10000 Hz
Adjusts the frequency above which the high-
frequency content of the reverb sound will be
reduced, or “damped.”
High Damp 1–100%
Adjusts the amount of damping applied to the
frequency range selected with HF Damp. With a
setting of “100%,” there will be no reduction of
the reverb’s high-frequency content.
High Cut 1000–10000 Hz
Adjusts the frequency above which the high-
frequency content of the reverb will be
reduced.
Parameter Value Description
V-Synth_GT_v2_e1.book 16 ページ ２００８年１２月１７日 水曜日 午前９時５分