Ropex 740303 - Default Chapter; Table of Contents

Page 2 RES-403 Version 1
Contents
1 General information . . . . . . . . . . . . . . . . . . 3
1.1 Copyright . . . . . . . . . . . . . . . . . . . . . . . 3
1.2 Intended use . . . . . . . . . . . . . . . . . . . . 3
1.3 Heatsealing band . . . . . . . . . . . . . . . . 3
1.4 Impulse transformer . . . . . . . . . . . . . . 4
1.5 Current transformer PEX-W4/-W5 . . . . 4
1.6 Line filter . . . . . . . . . . . . . . . . . . . . . . . 4
1.7 Maintenance . . . . . . . . . . . . . . . . . . . . 4
1.8 Transportation . . . . . . . . . . . . . . . . . . . 4
1.9 Disposal . . . . . . . . . . . . . . . . . . . . . . . . 5
2 Application . . . . . . . . . . . . . . . . . . . . . . . . . . 7
3 Principle of operation . . . . . . . . . . . . . . . . . 7
4 Traits of the controller . . . . . . . . . . . . . . . . 7
5 Installation . . . . . . . . . . . . . . . . . . . . . . . . . . 8
5.1 Installation procedure . . . . . . . . . . . . . 8
5.2 Installation steps . . . . . . . . . . . . . . . . . 9
5.3 Power supply . . . . . . . . . . . . . . . . . . . 10
5.4 Line filter . . . . . . . . . . . . . . . . . . . . . . 11
5.5 Current transformer PEX-W4/-W5 . . . 11
5.6 Wiring diagram (Standard) . . . . . . . . 13
5.7 Wiring diagram with booster
connection (MOD 26) . . . . . . . . . . . . 14
5.8 Wiring diagram with "Temp-
erature reached" signal (MOD 40)
or „Temp. OK“ signal (MOD 46) . . . . 15
5.9 Startup and operation . . . . . . . . . . . . 16
5.10 View of the controller . . . . . . . . . . . . . 16
5.11 Controller configuration . . . . . . . . . . . 16
5.12 Replacing and "burning in" the heat-
sealing band . . . . . . . . . . . . . . . . . . . 18
5.13 Startup procedure . . . . . . . . . . . . . . . 19
6 Controller functions . . . . . . . . . . . . . . . . . 20
6.1 Indicators and controls . . . . . . . . . . . 21
6.2 Temperature setting (set point selection)
22
6.3 Temperature indication (actual value
output) . . . . . . . . . . . . . . . . . . . . . . . . 23
6.4 Automatic zero calibration (AUTOCAL) .
25
6.5 "START" signal (HEAT) . . . . . . . . . . . 26
6.6 Measuring impulse duration
(as of October 2005) . . . . . . . . . . . . . 28
6.7 Automatic phase angle
compensation (AUTOCOMP)
(as of October 2005) . . . . . . . . . . . . . 28
6.8 Temperature diagnosis
(as of October 2005) . . . . . . . . . . . . . 30
6.9 Heatup timeout
(as of October 2005) . . . . . . . . . . . . . 32
6.10 Diagnostic interface/visualization software
(as of October 2005) . . . . . . . . . . . . . 32
6.11 System monitoring/alarm output . . . . 33
6.12 Error messages . . . . . . . . . . . . . . . . . 34
6.13 Fault areas and causes . . . . . . . . . . . 39
7Factory settings. . . . . . . . . . . . . . . . . . . . . 40
8 Technical data . . . . . . . . . . . . . . . . . . . . . . 42
9 Dimensions . . . . . . . . . . . . . . . . . . . . . . . . 44
10 Modifications (MODs) . . . . . . . . . . . . . . . . 44
11 How to order . . . . . . . . . . . . . . . . . . . . . . . . 46
12 Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48