Why does my Roundup VCT-2000 burn buns when the display flashes “LO”?
If the Roundup Toaster control display flashes “LO” continuously and the buns burn, it indicates a failed platen thermocouple. It's recommended to contact your maintenance person or an authorized service agency for service.
Why does the Roundup Toaster control display flash “HI” continuously and buns are not toasting properly?
If the Roundup Toaster control display flashes “HI” continuously and the buns are not toasting properly, it indicates a loose platen thermocouple connection on the control board or that the platen thermocouple is open. Try re-securing the platen thermocouple connection to the control board. If the control display still reads “HI”, check the thermocouple for continuity. If the issue persists, contact your maintenance person or an Authorized Service Agency.
How to troubleshoot a Roundup Toaster when the display flashes “HI” and buns don't toast?
If the Roundup Toaster control display flashes “HI” continuously and the buns are not toasting properly, it could be due to a loose platen thermocouple connection on the control board or an open platen thermocouple. Try re-securing the platen thermocouple connection to the control board. If the display continues to read “HI”, check the thermocouple for continuity. If problems persist, it's recommended to contact your maintenance person or an authorized service agency for assistance.
Why does the Roundup Toaster control display flash “HI” continuously and buns burn?
If the Roundup Toaster control display flashes “HI” continuously and the buns burn, it indicates a failed platen solid state relay. Contact your maintenance person or Authorized Service Agency for service.
What does it mean when the Roundup Toaster control display flashes “HI” & “LO” then “HI” & “USE”?
If the Roundup Toaster control display flashes “HI” & “LO” at cold start up, then “HI” & “USE” after 20–30 minutes, it suggests a loose auxiliary thermocouple connection on the control board or that the thermocouple is open. Try re-securing the auxiliary thermocouple connection to the control board. If the control display still reads “HI” & “LO” or “HI” & “USE”, check the thermocouple for continuity. If problems persist, contact your maintenance person or Authorized Service Agency.
How to fit new conveyor belt wraps on Roundup Oven?
If new Conveyor Belt Wraps don't fit, it might be due to incorrect Compression Settings (set Compression Knobs to 6 and 6 when replacing Belt Wraps or adjusting Conveyor Belt Chains), Belt Wraps not installed correctly (install inside the Yellow Support Rods with the “zipper flap” exposed), or Non-OEM or damaged Belt Wraps used (replace with OEM Belt Wraps).
What does it mean when Roundup Oven control display flashes “LO” continuously and buns burn?
The control display flashing “LO” continuously while buns burn indicates a failed Platen Thermocouple.
What to do if the control display flashes “HI” continuously and the buns are not toasting properly on my Roundup Toaster?
If the control display flashes “HI” continuously and the buns are not toasting properly on your Roundup Toaster, re-secure the Platen Thermocouple connection to the Control Board. If the Control Display still reads “HI”, check the Thermocouple for continuity.
Why is the control display flashing 'LO' continuously and the buns are not toasting properly on my Roundup VCT-2000?
If the control display flashes “LO” continuously and the buns aren't toasting properly on your Roundup Toaster, it could be because the platen temperature is below 440ºF (226ºC). Let the unit warm up for 30 minutes and then check again.
Why does the control display flash “CHEC” continuously on my Roundup VCT-2000 Toaster?
The control display flashes “CHEC” continuously on your Roundup Toaster if the control compartment temperature is above 140ºF (60ºC). Make sure that the side vents on the toaster are not blocked and that the toaster is not near other heating appliances.
Overview of the VCT-2000, warranty coverage, exclusions, and service access.
Essential precautions for safe operation, including electrical hazards and grounding.
Guide for using the toaster, setting controls, and temperature adjustments.
Detailed steps for daily cleaning of the toaster and care for release sheets/belt wraps.
A table listing common problems, their causes, and corrective actions.
Details warranty, exclusions, and procedures for handling shipment damage.
To Next Page
General
