Samson 3351 - Page 76

14-16 EB 8039 EN
UK DECLARATION OF INCORPORATION DC061
2022-12
SAMSON REGULATION SAS • 1 rue Jean Corona • 69120 Vaulx-en-Velin
Tel.: +33 (0)4 72 04 75 00 • E-mail: france@samsongroup.com • Internet: www.samson.fr
BNP Paribas
N° compte 0002200215245 • Banque 3000401857
IBAN FR7630004018570002200215245 • BIC (code SWIFT) BNPAFRPPVBE
Société par actions simplifiée au capital de 10 000 000 € • Siège social : Vaulx-en-Velin
N° SIRET: RCS Lyon B 788 165 603 00127 • N° de TVA: FR 86 788 165 603 • Code APE 2814Z
Crédit Lyonnais
N° compte 0000060035B41 • Banque 3000201936
IBAN FR9830002019360000060035B41 • BIC (code SWIFT) CRLYFRPP
Page 1
WEEE N° FR025665
Declaration of Incorporation of Partly Completed Machinery
In accordance with Schedule 2 Part 2 Annex II, section 1.B of the Directive 2008 No. 1597 Supply of Machinery
(Safety) Regulations 2008
For the following products:
Type 3351 Pneumatic ON/OFF Valve
We certify that the Type 3351 Pneumatic ON/OFF Valves industries are partly completed machinery as defined
in the Directive 2008 No. 1597 Supply of Machinery (Safety) Regulations 2008 and that the safety
requirements stipulated in Annex I, 1.1.2, 1.1.3, 1.1.5, 1.3.2, 1.3.4 and 1.3.7 are observed. The relevant
technical documentation described in Annex VII, (Part 7 of Schedule 2) part B has been compiled.
Products we supply must not be put into service until the final machinery into which it is to be incorporated has
been declared in conformity with the provisions of the Directive 2008 No. 1597 Supply of Machinery (Safety)
Regulations 2008.
Operators are obliged to install the products observing the accepted industry codes and practices (good
engineering practice) as well as the mounting and operating instructions. Operators must take appropriate
precautions to prevent hazards that could be caused by the process medium and operating pressure in the
valve as well as by the signal pressure and moving parts.
The permissible limits of application and mounting instructions for the products are specified in the associated
data sheets as well as the mounting and operating instructions; the documents are available in electronic form
on the Internet at www.samsongroup.com.
For product descriptions of the valve, refer to Mounting and Operating Instructions EB 8039.
Referenced technical standards and/or specifications:
▪ VCI, VDMA, VGB: "Leitfaden Maschinenrichtlinie (2006/42/EG) — Bedeutung für Armaturen, Mai 2018"
[German only]
▪ VCI, VDMA, VGB: "Zusatzdokument zum „Leitfaden Maschinenrichtlinie (2006/42/EG) — Bedeutung für
Armaturen vom Mai 2018" [German only], based on DIN EN ISO 12100:201 1-03
Comments:
▪ See mounting and operating instructions for residual hazards.
▪ Also observe the referenced documents listed in the mounting and operation instructions.
Persons authorized to compile the technical file:
SAMSON REGULATION SAS – 1 rue Jean Corona – FR-69120 VAULX-EN-VELIN
Vaulx-en-Velin, 23
rd
December 2022
Bruno Soulas
General Director
Head of Strategy and Development
Joséphine Signoles
-Fontaine
Head of QSE department