- 31 -
䣑䣍
䣷䣵䣕䣶 䣣 䣶
䣮䣵䣖䣱䣱
䣎䣱䣩
䣕䣧 䣶
䢷䢰䢲䢲䢵䢹 䢰
䣗䣏䣇䣐
䣑䢴䢰䢲䢧䢴䢷䣅䣑䢰䢲䤑䣅䣲䢵䢹䣖䣧䣯
䣅䣣 䣰䣥 䣧 䣮
䢴䢶䢳䢴䢲
䣅䣮䣧䣣䣴
䣒䣅 䣃 䣮 䣮
䣒䣅 䢳 䣆
䣏䣇䣐䣗
䢹䢱䢷䢱䢳䢴䢲䢳䢲䢷䢲䤑䣅
㻼㻯 㻚㼍㼠㼛㼛㼓 㼐㻿 䣧 㼚㼐 㼘
䢱䢳䢹䢲䢱䢲䢷䢴䢲䢳䣆䣣 䣶 䣣䣎䣱䣩
䣧䣮䣅䣣 䣰䣥
䣕䣶 䣣 䣴 䣶
㼍㼠
䣏䣇䣐䣗
䣵䣵䣱䣩䣴䣧䣒䣴
㻼㻯 㻚㼠㼛㼓㼐 㼍㻿 䣧 㼚㼐 㼘㼛
䢸䢴䢷䢰䢰䢰䣦䣫䣰䣩䣕䣧䣰
䢳䢹䢱䢲䢷䢱䢴䢲䢳䢲䣣䣶䣣䣎䣱䣩 䣆
䣮䣣䣰䣥䣧
䣶䣣䣴䣶䣕
㼍㼠
䣅
䣇䣐䣗䣏
䣵䣵䣱䣩䣴䣧䣒䣴
䢷䢸䢴䣧䣦䢰 䢰䣈䣫䣰䣫䣵䣪
䢳䢹䢱䢲䢷䢱䢴䢲䢳䢲䣣䣶䣣䣱䣩 䣆䣎
䣮䣅䣣䣰䣥䣧
㻯㻚㼠㼛 㻼㼍㼠㼍㼛㼓 㼐㼚㼐 㼘㻿 䣧
䣕䣶 䣣 䣴 䣶
䣏䣇䣐䣗
䣵䣵䣱䣩䣴䣧䣒䣴
㻌
㻌
㻌
㻌
㻌 㻌䠘Transferring 1day Log data to PC>
Note) It is necessary to set Hyper terminal in PC side.
In Top Screen is displayed and press MENU key and select “Log”.
Press ENTER key to display Log data.
Display required Log data by pressing left and right shift key (䊹㻌 䊻).
Display MENU key and select “PC 1D” and press ENTER key to display “Progress” in the upper left side.
Select “Start” in MENU key and press ENTER key to transfer 1day Log data to PC with displaying “Sending..”
and quantity of transferring data in the lower side.
“Finished..” will be displayed when transferring 1day Log data is complete.
Note) Select “Cancel” in MENU key and press ENTER key to return to Top Screen.
㻌
䢴 䢶䢴䢳䢲
䣥 䣧 䣮䣅 䣣 䣰
䣅 䣮 䣧 䣣 䣴
䣃 䣮 䣮䣒 䣅
䣒 䣅 䢳 䣆
䣗䣏 䣇 䣐
䢳 䢹䢲 䢱 䢷 䢱䢴 䢲 䢳䣅䢷 䢲 䤑
㻌
<Transferring all Log data to PC>
Note) It is necessary to set Hyper terminal in PC side.
In Top Screen is displayed and press MENU key and select “Log”.
Press ENTER key to display Log data.
Display required Log data by pressing left and right shift key (䊹㻌 䊻).
Display MENU key and select “PC All” and press ENTER key to display “Progress” in the upper left side.
Select “Start” in MENU key and press ENTER key to transfer all Log data to PC with displaying “Sending..”
and quantity of transferring data in the lower side.
“Finished..” will be displayed when transferring 1day Log data is complete.
Note) Select “Cancel” in MENU key and press ENTER key to return to Top Screen.
<Setting in PC for transferring log data> (For Windows 2000 and Windows XP)
From Window Start Button, select Program – Accessories – Communications – HiperTerminal to start
the HyperTerminal. (If the HyperTerminal is not available from the Start Menu, execute the following file:
C:¥Program Files¥Windows NT¥hypertrm.exe.)
In the HyperTerminal Window, set a new connection, the name (for example, Sanyo), connection settings,
Method of connection, COM1, properties of COM1, and port.
Baud rate: 9,600, Data bits: 8, Parity:None, Stop bits:1, Flow control: Xon/Xoff
(The communications condition of the Incubator will be set automatically to the above settings when the
Progress Display appears.)
Note) Optional RS232C/RS485 Interface MTR-480 (RS-232C/RS-485) is required to transfer data.
To Next Page
Loading...
