Sanyo MCO-19M - Page 47

- 44 -
㻌
㻌
㻌
7. Setting of Date and time
㻌
㻌
䣑 䣍
䣷 䣵䣕 䣶 䣣 䣶
䣖 䣱 䣱 䣮 䣵
䣎 䣱 䣩
䣕 䣧 䣶
䢷 䢰 䢲䢲䢵 䢹 䢰
䣗䣏 䣇 䣐
䣑 䢴䢰 䢲 䢧䢴 䢷䣅 䣑䢰 䢲 䤑䣅䣲 䢵 䢹䣖 䣧 䣯
㻌
㻌
㻌
㻌
䣧䣖 䣫 䣯䣆 䣣 䣶 䣧
䣫 䣰 䣩䣕 䣧 䣶 䣶䣒 䣙䣎 䣱 䣥 䣭䣍 䣧 䣻
䣰 䣩䣧 䣶 䣶 䣫䣗 䣘 䣕
䣥 䣧 䣮䣅 䣣 䣰
䣫 䣰 䣩䣕 䣧 䣶 䣶䣆 䣃 䣓䣎 䣅 䣆 䢱
䣕 䣸 䣥
䣫 䣰 䣩䣕 䣧 䣶 䣶䣣 䣴 䣯
䣑
䣃 䣮
䣍
䣰䣣 䣶 䣫 䣱䣮 䣫 䣤 䣴䢴 䣅 䣣䣑 䢴 䢱 䣑䣯 䣲 䢱 䣅䣖 䣧
䣗䣏 䣇 䣐
䢫䢪 䢳 䢱 䢴
䣱 䣮 䣵䣶 䣖 䣱䣧 䣮 䣧 䣥䣕
㻌
㻌
㻌
㻌
䣆 䣣 䣶 䣧 䣖 䣫 䣯 䣧
䣆 䣣 䣶 䣧 䢳 䢲 䢱 䢲 䢷 䢱 䢳 䢹 䢪 䣛 䣛 䢱 䣏 䣏 䢱 䣆 䣆 䢫
䣖 䣫 䣯 䣧 䢳 䢺 䢼 䢶 䢷 䢼 䢵 䢺 䢪 䣪 䣪 䢼 䣯 䣯 䢼 䣵 䣵 䢫
䣎 䣱 䣩 䣋 䣰 䣶 䣧 䣴 䣸 䣣 䣮 䢸 䣯 䣫 䣰 䢪 䢴 䢯 䢵 䢲 䣯 䣫 䣰 䢫
㻌
<Setting of date and time>
Ex䠅 How to set 6:45:38 p.m. on May 17
th
2010
Procedures MENU key
0 In Top Screen, press MENU key and select “Tools”. Tools
1 Press ENTER key and select “Date Time” in the “Select Tools (1/2)” display.
2 Press MENU key and select “OK”. OK
3 Press ENTER key and input “100517” in the right side of “Date” column in the “Date
Time” display.
4 Press ENTER key and input “184538” in the right side of “Time” column.
5 Press MENU key and select “OK”. OK
6 Press ENTER key and “Select Tools (1/2)” display is appeared.
<Setting of Log intervals>
㻌㻌㻌㻌㻌
㻌㻌㻌㻌The intervals for acquiring log data.
Input a value in the right side of “Log Interval” column in the “Date Time” display.
Press MENU key and select “OK” and press ENTER key.
㻌
㻌㻌㻌㻌Input range is 2~30 minutes (Factory default: 6 minutes)
Note) When you input a value lower than “2”, Log interval is automatically set in 2 minutes.
When you input a value higher than “30”, Log intervals is automatically set in 30 minutes.
㻌
㻌