EasyManua.ls Logo

Sanyo PLC-ET30L - Page 67

Sanyo PLC-ET30L
154 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Loading...
-67-
Electrical Adjustment
Group/Item Item Name Function Initial Range Note
151 DCOffset_B_17
0
0
0-2047
Normal
Reversed Left/Right
152 DCOffset_B_18
0
0
0-2047
Normal
Reversed Left/Right
153 DCOffset_B_19
2032
0
0-2047
Normal
Reversed Left/Right
154 DCOffset_B_20
0
0
0-2047
Normal
Reversed Left/Right
155 DCOffset_B_21
0
0
0-2047
Normal
Reversed Left/Right
156 DCOffset_B_22
0
2032
0-2047
Normal
Reversed Left/Right
157 DCOffset_B_23
0
0
0-2047
Normal
Reversed Left/Right
158 DCOffset_B_24
0
0
0-2047
Normal
Reversed Left/Right
102 Panel Service (7200)
0 SoftRstR 1 0-7
1 SoftRstG 1 0-7
2 SoftRstB 1 0-7
3 SoftRstDisR 0 0-1
4 SoftRstDisG 0 0-1
5 SoftRstDisB 0 0-1
6 OutputDisR 0 0-1
7 OutputDisG 0 0-1
8 OutputDisB 0 0-1
103 Panel Service (9020)
0 F00_R R/L, U/D, Data Reversed, DX, DY Reversed 8 0-4095
1 F00_G 9 0-4095
2 F00_B 8 0-4095
3 F02_R Precharge ON/OFF 1 0-4095
4 F02_G 1 0-4095
5 F02_B 1 0-4095
6 F05_R Precharge2 Output Setting(+) 4032 0-4095
7 F05_G 4032 0-4095
8 F05_B 4032 0-4095
9 F06_R Precharge2 Output Setting(+) 3584 0-4095
10 F06_G 3584 0-4095
11 F06_B 3584 0-4095
12 F07_R Precharge2 Output Setting(-) 1024 0-4095
13 F07_G 1024 0-4095
14 F07_B 1024 0-4095
15 F08_R Fixed 2048 0-4095
16 F08_G 2048 0-4095
17 F08_B 2048 0-4095
18 F09_R VCOM Output Voltage Setting 120 0-4095 * Common Voltage Adj. [R]
19 F09_G 120 0-4095 * Common Voltage Adj. [G]
20 F09_B 120 0-4095 * Common Voltage Adj. [B]
21 F0A_R Number of Outputs 3 0-4095
22 F0A_G 3 0-4095
23 F0A_B 3 0-4095
24 F0E_R Rotation Order 1 0-4095
25 F0E_G 1 0-4095
26 F0E_B 1 0-4095
27 F0F_R Rotation Mode 32 0-4095
28 F0F_G 32 0-4095
29 F0F_B 32 0-4095
200 Option
0 Logo Prohibition 0: Menu / 1: rohibition / 2: China /3-9: not used 0 0-2
1 RS232C Baudrate 0: 19200bps, 1: 9600bps 0 0-1
2
3 Shipping Setting Sets when the value is set to 10. 0 0-20
4
5 PW Debug Command Enable
0: Disable (Serial Command Eanble)
1: Enable (PW Debug Mode)
0 0-1
6 Device Refresh Disable
0: Enable
1: Disable
0 0-1
20 Projector Time Reset Resets when the value is set to 10. 1 0-10
21 Lamp Warning Time (NORMAL) Lamp Warning Time at Normal Mode 1-16

Table of Contents

Other manuals for Sanyo PLC-ET30L

Related product manuals