Sanyo PLC PLC-ET30L - Page 71

-71-
Electrical Adjustment
Group/Item Item Name Function Initial Range Note
0 Lamp Voltage Current Lamp Voltage (V) --- 0-255
1 Lamp Vol Threshold Voltage to judge the lower voltage (V) 30 30-90
2 Fan1 Speed Gain 300 0-1500
257 Fan Setting at Dimmer
0 Dimmer Average Check Period
Check Period of Avarage Dimmer
0: 10, 1: 30, 2: 60, 3: 90 … 10: 300 sec.
1 0-10
260 Auto Calibration
0 Execute Calibration
Executes Auto Calibration when the value is changed.
(For PC White 100%)
0 0-1 * Auto Calibration Adj.
1 Loop Count 8 1-30
2 Auto Status
Result of the Auto Calibration
0: End normally, 1: Adjusting, 9: Error
0 0 / 1 / 9
3 AutoWait 3 1-20
4 CHECK-Tolerance 4 1-255
5 Time out wait 20 1-255
261 Auto Calibration (RGB)
0 OFFSET AREA H START 975 0-1000
1 OFFSET AREA V START 500 0-1000
2 GAIN AREA H START 25 0-1000
3 GAIN AREA V START 500 0-1000
4 Image AREA H WIDTH 13 0-4095
5 Image AREA V HIGHT 9 0-4095
6 OFFSET Target 20 0-1023
7 OFFSET Tolerance 1 1-1023
8 GAIN Target 955 0-1023
9 GAIN Tolerance 1 1-1023
10 Image Level Tolerance 2 1-255
262 Auto Calibration (CVBS/SVIDEO)
0 Y Image Area Start X 20 0-1000
1 Y Image Area Start Y 200 0-1000
6 Image Area H Width 8 0-4095
7 Image Area V Hight 9 0-4095
8 Y Target Level 875 0-1023
11 Gain Tolerance 1 1-255
12 Image Level Tolerance 2 1-255
264 Auto Calibration (YCbCr)
0 Y-OFFSET AREA H START 925 0-1000
1 Y-OFFSET AREA V START 500 0-1000
2 CB-OFFSET AREA H START 925 0-1000
3 CB-OFFSET AREA V START 500 0-1000
4 CR-OFFSET AREA H START 925 0-1000
5 CR-OFFSET AREA V START 500 0-1000
6 Y-GAIN AREA H START 50 0-1000
7 Y-GAIN AREA V START 500 0-1000
8 CB-GAIN AREA H START 800 0-1000
9 CB-GAIN AREA V START 500 0-1000
10 CR-GAIN AREA H START 700 0-1000
11 CR-GAIN AREA V START 500 0-1000
12 Image AREA H WIDTH 13 0-4095
13 Image AREA V HIGHT 9 0-4095
14 Y-OFFSET TARTGET 4 0-1023
15 CB OFFSET TARGET 512 0-1023
16 CR OFFSET TARGET 512 0-1023
17 Y-GAIN TARGET 810 0-1023
18 CB-GAIN TARGET 894 0-1023
19 CR-GAIN TARGET 894 0-1023
20 OFFSET Tolerance 1 1-255
21 GAIN Tolerance 1 1-255
22 Image Level Tolerance 2 1-255
280 AutoPC Adjsut
0 AutoPCAdjustEnable 0 0-1
1 Frequency Step 1 0-3
2 Frequency Threshold 5 0-10
3 Fine Phase 1 0-1
4 BLKDET 1 0-7
5 PHASEMSK 0 0-3