To Next PageTo Next PageWhat does it mean when the LAMP REPLACE indicator lights yellow on my Sanyo PLC-SW30 Projector?
Replace the projection lamp with a new one promptly. Reset the Lamp replace counter after replacement of the lamp.
What does it mean when the LAMP REPLACE indicator lights yellow on Sanyo PLC-SW30?
If the LAMP REPLACE indicator lights yellow on your Sanyo Projector, it means you should promptly replace the projection lamp with a new one. Remember to reset the Lamp replace counter after replacing the lamp.
What to do if the Sanyo PLC-SW30 Projector cannot be turned on due to high temperature?
If your Sanyo Projector won't turn on because of high temperature, it means the internal temperature is too high. Allow the projector to cool down. Once the temperature returns to normal, the POWER indicator will light red, and you can turn the projector on. Also, check and clean the air filter to prevent this issue.
What to do if my Sanyo PLC-SW30 projection lamp is nearing the end of its life?
If the indicator light turns yellow, it means the projection lamp in your Sanyo Projector is nearing the end of its life. Replace the lamp with a new one as soon as possible. After replacing the lamp, remember to reset the lamp replacement counter.
What to do if the Sanyo PLC-SW30 Projector detects an abnormal condition and cannot be turned on?
Unplug the AC power cord and plug it in again to turn on the projector. If the projector turns off again, disconnect the AC power cord.
What to do if Sanyo PLC-SW30 is not turning on due to an abnormal condition?
If the Sanyo Projector is not turning on and you suspect it's due to an abnormal condition, unplug the AC power cord, then plug it back in to attempt to turn the projector on. If the projector turns off again, disconnect the AC power cord and contact your dealer or a service center for assistance. Do not leave the projector on, as this could pose a risk of electric shock or fire.
Why is my Sanyo PLC-SW30 not turning on due to high temperature?
If the Sanyo Projector is not turning on because of high temperature, it means that the temperature inside the projector is abnormally high. When the projector cools down sufficiently and the temperature returns to normal, the POWER indicator will light red, and you will be able to turn the projector on. Also, check and clean the air filter.
General| Native aspect ratio | 4:3 |
|---|---|
| Projection distance | - m |
| Vertical scan range | 50 - 100 Hz |
| Horizontal scan range | 15 - 80 kHz |
| Projection technology | 3LCD |
| Contrast ratio (typical) | 300:1 |
| Screen size compatibility | 34 - 200 \ |
| Projector native resolution | SVGA (800x600) |
| Keystone correction, horizontal | 20 ° |
| Lamp type | UHP |
| Lamp power | 150 W |
| Light source type | Lamp |
| Service life of light source | 2000 h |
| Service life of light source (economic mode) | 2500 h |
| RMS rated power | 0.8 W |
| Number of built-in speakers | 1 |
| Power source | AC |
| AC input voltage | 100 - 240 V |
| Power consumption (standby) | - W |
| Power consumption (typical) | 244 W |
| Power consumption (PowerSave) | 169 W |
| Focus | Manual |
| Throw ratio | 1.6 - 1.9:1 |
| Focal length range | - mm |
| Aperture range (F-F) | 1.6 - 1.8 |
| HDCP | - |
| Noise level | - dB |
| Dot clock scanning frequency | 100 MHz |
| Full HD | No |
| Analog signal format system | NTSC, NTSC 4.43, PAL, PAL M, PAL N, SECAM |
| Supported graphics resolutions | 800 x 600 (SVGA) |
| USB connector type | USB Type-B |
| HDMI ports quantity | 0 |
| Serial interface type | RS-232 |
| USB 2.0 ports quantity | USB 2.0 ports have a data transmission speed of 480 Mbps, and are backwards compatible with USB 1.1 ports. You can connect all kinds of peripheral devices to them. |
| Placement | Desktop |
| Product type | Standard throw projector |
| Product color | Black, White |
| Cables included | AC, VGA |
| Remote control type | IR |
Weight and Dimensions| Depth | 190 mm |
|---|---|
| Width | 270 mm |
| Height | 78 mm |
| Weight | 2100 g |
