Sanyo PLC-ZM5000 - Page 58

Choose the running speed of cooling fans from the
following options.
Normal .. Operate in this mode under normal
conditions.
Max........ Use this mode when you want to increase the
cooling effect when operating the projector in
high ambient temperature environment. Fan
noise is louder than Normal.
Setting
Simple mode buttons
Only these buttons are
active when the simple
mode is set to On. [ON,
STAND-BY, SHUTTER,
INPUT, MENU, AUTO
3&6&5((1Ÿź
087(Ż92/80(
Ź92/80(
SELECT (Mouse Pointer
included), L-CLICK,
R-CLICK, P-TIMER,
POINTER, PIP, ON-OFF
switch] Number buttons
(p.14) also become
active only when setting
the remote control codes
numbers or entering the
PIN code numbers (pp.
54, 62).
Filter control
This function decides whether to activate the simple mode.
Off . . . Simple mode function is off.
On....Only the simple mode buttons are active.
<RXFDQUHSODFHWKH¿OWHUZLWKWKLVIXQFWLRQ3UHVVWKH
SELECT button at
Filter control
WRGLVSOD\DFRQ¿UPDWLRQ
box. To replace, press the SELECT button at
Yes
and the
HOHFWULFDOO\RSHUDWHG¿OWHUVWDUWVWR scroll.
3
Note:
)LOWHUUHSODFHPHQWLFRQDQG
Please wait...
PHVVDJH
DSSHDURQWKHVFUHHQZKHQWKH¿OWHULVEHLQJVFUROOHG
7KH¿OWHUFDQQRWEHUHZRXQG
:KHQWKH¿OWHULVUHSODFHGWKHWRWDODFFXPXODWHGWLPHRI
WKH¿OWHUXVHLVDXWRPDWLFDOO\VHWWR
0

A confirmation box appears
and then select Yes.
The eight different remote control codes (Code 1- Code 8)
are assigned to the projector; the factory-set, initial code
(Code 1) and the other seven codes (Code 2 to Code 8).
The same code should be set on both the projector and
the remote control. For example, operating the projector in
Code 7, the remote control code also must be switched to
Code 7.
To change the code for the projector:
Select a remote control code in this Setting Menu.
To change the code for the remote control:
Press and hold the MENU button and a number button
(1-8) on the remote control for more than five seconds to
switch among the codes. See “Remote Control Code” on
page 16.
3Note:
:KHQGLIIHUHQWFRGHVDUHVHWRQWKHSURMHFWRUDQGRQ
WKHUHPRWHFRQWUROQRRSHUDWLRQFDQEHPDGH,QWKDW
FDVHVZLWFKWKHFRGHRQWKHUHPRWHFRQWUROWRILWWKH
FRGHRQWKHSURMHFWRU
,IWKHEDWWHULHVDUHUHPRYHGIURPWKHUHPRWHFRQWURO
IRUDORQJSHULRGRIWLPHWKHUHPRWHFRQWUROFRGHZLOO
EHUHVHW
Filter control
Fan control
Simple mode
Remote control
3Note:
:DUQLQJLFRQDQGSimple mode : OnPHVVDJHDSSHDU
RQ WKH VFUHHQ IRU DERXW  VHFRQGV ZKHQ SUHVV WKH
EXWWRQZKLFKLVQRWWKHVLPSOHPRGHEXWWRQ
58