Scheppach sd1600v User Manual

www.scheppach.com
30
|
GB
7.3 Install the scroll saw on the workbench
You require the following for assembly:
• M8 hexagonal bolt (4x)
• M8 hexagonal nut (4x)
• Washer Ø 8.4 mm (8x)
(not included in the scope of delivery)
The length of the screws to be used vary depending on
the thickness of the tabletop.
m WARNING
Danger of injury! Disconnect the mains plug on the
scroll saw before all assembly work.
1. Mount the scroll saw on a solid wooden work-
bench. This way, a high noise level due to vibra-
tions can be avoided.
2. Mark the drill holes (see g. 5.2).
3. Drill the 4 holes (diameter 8 mm) into the work-
bench.
4. Screw the scroll saw onto the workbench with the
hexagonal bolt (E) through the assembly points
(g. 3 pos. 19) in the following sequence (g. 5.1):
D Hexagonal nut
C Washer
A Scroll saw
B Workbench
C Washer
E Hexagonal bolt
5. Tighten the hexagonal nuts (D).
8. Layout
m WARNING
Danger of injury! Disconnect the mains plug on the
scroll saw before all assembly work.
8.1 Installing the saw blade guard (5) and the re-
taining device (23) (g. 6, 7)
NOTE:
Before assembling the retaining device (23), the saw
blade pre-installed at the factory (21) must be removed
(see 8.2).
1. Remove the saw blade (21) as described in 8.2.
2. Remove the retaining device (23) from the saw
blade guard (5): Loosen the screw (24) complete-
ly using a Phillips screwdriver (not included in the
scope of delivery) (see g. 6).
The permitted workstation values can also vary from
country to country. However, this information should
enable the operator to better evaluate the hazards and
risks.
Limit the noise level to a minimum!
• Only use faultless devices.
• Maintain and clean the device at regular intervals.
• Adapt your working methods to the device.
• Do not overload the device.
• Have the device checked if necessary.
• Switch the device off if it is not in use.
Suitable saw blades
All industry-standard saw blades with a minimum
length of 127 mm with and without a pin may be used.
7. Before commissioning
7.1 Unpacking
• Open the packaging and carefully remove the de-
vice.
• Remove the packaging material, as well as the pack-
aging and transport safety devices (if present).
• Check whether the scope of delivery is complete.
• Check the device and accessory parts for transport
damage.
• If possible, keep the packaging until the expiry of the
warranty period.
m WARNING
The device and the packaging are not children‘s
toys! Do not let children play with plastic bags,
lms or small parts! There is a danger of choking
or suffocating!
7.2 General notes
• Prior to commissioning, all covers and safety devic-
es must be mounted correctly.
• The saw blade must be able to run freely.
• In case of previously machined wood, be aware of
any foreign bodies, such as nails or screws, etc.
• Before pressing the on/off switch, make sure that the
saw blade is correctly tted, and that moving parts
run smoothly.
• Before connecting the machine, make certain that
the data on the type plate matches with the mains
power data.
• Only connect the machine to a correctly installed
protective contact socket, with fuse protection of at
least 10 A.

Scheppach sd1600v Specifications

General

Blade length	134 mm
Throat depth	406 mm
Product color	Black, Blue
Stroke height	50 mm
Idle speed (max)	1700 RPM
Idle speed (min)	500 RPM
Table tilt range	0 - 45 °
Maximum power	120 W
AC input voltage	220-240 V
AC input frequency	50 Hz

Weight and Dimensions

Depth	630 mm
Width	295 mm
Height	370 mm
Weight	12700 g
Table depth	415 mm
Table width	255 mm