Sega Transformers Human Alliance - Page 22

84 pages

To Next Page

To Previous Page

GROUNDING

Fully insert the power cord connector on the side opposite the power plug into the AC

unit inlet.

Fully insert the power cord plug into the outlet.

The power cord is laid out indoors. Protect the power cord by attaching wire cover to it.

7. INSTALLATION

http://op.sega.jp/op_e/

Main Page

List of Third-Party Rights2
Before Using the Product, be Sure to Read the Following4
Table of Contents8
Specifications10
Warning Labels/Drawings/Warning Labels Position12
Game Machine Installation Location13
Dimension14
Parts Descriptions15
Accessories List16
Installation17
Location of the Parts17
Work Procedures18
Install the Billboard Lamp20
Power Supply and Other Connections21
Precautions When Moving the Machine23
9．Game Introduction26
How to Play26
Game Test Mode39
Switch Unit and Coin Meter39
Game Test Mode40
Bookkeeping41
Input Test44
Output Test45
Game Assignments46
Controller Calibration Setting47
Backup Data Clear50
Repair & Maintenance for Controller Part51
Repair and Maintenance for Motor51
Repair and Maintenance for Controller Handle Infrared51
Repair and Maintenance for Mobile Potentiometer (Left and Right)52
Repair and Maintenance for the Mobile Potentiometer (up and Down)52
Repair and Maintenance for LED Panel53
Doesn't Work in the Input Test53
Unscrew and Remove the STAR BUTTON PLATE53
Remove the Micro-Switch from the Lamp Housing53
Remove the Wiring Harness from the Old Micro-Switch and Re-Attach It to the Replacement Switch in the same Manner54
13． Maintenance for Other Components54
Repair and Maintenance for the Brake Light Panel54
On both Sides of the Plate Lamp Maintenance54
Maintenance for the Control Table Lamp55
Graphics Display57
LCD Component57
Button Names and Functions57
Cleaning & Maintenance for Coin Selector58
Handling the Coin Jam58
Coin Insert Test59
How to Replace the Panel & Lighting Tube for Billboard59
Replace the Lamp Box & Lighting Tube59
Replace the Lamp Panel61
How to Replace the Lighting Bulb for Start Button62
Access to the Start Switch and Lamp Housing Is Gained by First Removing the Start Button Plate62
Remove the Button Plate from the Control Panel to Gain Access to the Switch and Lamp Housing62
Once the Button Plate Has Been Removed to Reveal the Switch and Lamp Housing, Do Not Pull the Assembly Arbitrarily, Otherwise, May Lead to the Damage63
Holding the Lamp Housing between Your Index Finger and Thumb, Gently Remove the63
Twisted in Its Housing63
Common Troubleshooting64
Start the Game , the Aim Point in the Screen Cannot be Movable When Swinging the Controller Left and Right64
Start the Game, the Aim Point in the Screen Cannot be Movable When Swinging the Controller up and down65
Mainframe Position66
Ringedge2 - Location66
Cleaning the Ringedge268
Composition of Ringedege269
Error Warnning Display70
Parts List73
Final Assembly Drawing（Trf-55-000074
Mainframe（Trf-55-010075
Control Board Cover Assemblies75
Front Cover (Left) for Controller Stand（Trf-55-030076
Front Cover (Right) for Controller Stand(TRF-55-0400)76
55' Controller Control Plate Assemblies(TRF-55-0500)77
LCD Wood Shell(TRF-55-0600)77
LCD Assemblies(TRF-55-0700)78
The Left Side Billboard Plate(TRF-55-0800)78
The Right Side of Billboard Plate(TRF-55-0900)79
Lighting Box Assemblies(TRF-55-1000)79
Controller Assemblies(TRF-GUN-0000)80
Control Board Wood Block(TRF-55-1100)80
Base Box Back Gate(TRF-55-1200)80
Base Box Side Gate(TRF-55-1300)80
Schematic Diagram81

Sega Transformers Human Alliance - Page 22

Table of Contents

Related product manuals