SensorTherm METIS H3 series

To Previous Page

Sensortherm GmbH

Hauptstraße 123

65843 Sulzbach

Tel: +49 (0)6196 64065-80

Fax: +49 (0)6196 64065-89

E-Mail: info@sensortherm.de

Internet: www.sensortherm.de

Metis_M308_M309_M313_M316_M318_M323_H309_H316_H318_12-pin (Sept. 21, 2018)

Main Page

Table of Contents2
General4
Information to this Manual4
CE Conformity and Standards4
Limitation of Liability4
Devices with PID Controller4
Terms of Warranty4
Copyright5
Explanation of Symbols5
Customer Service / Spare Parts5
Disposal5
Safety6
General6
Electrical Connection6
Laser Targeting Light6
Through-Lens Sighting / View Finder6
Device Labels6
Responsibility of the Operators6
Overview7
Intended Use7
Scope of Delivery7
Model Designs7
Electrical Connection8
Cable Colors and Pin Assignment (14-Wire Connection Cables)8
Factory Settings9
Power Supply9
Analog Output 1 and 210
Configurable Inputs / Outputs10
Serial Interface RS232 / RS485 (M3: Switchable RS232 / RS485; H3: Only RS485)11
Interface Converter (Accessory)12
Shielding12
Camera Module12
Devices with Additional Profibus-DP or Profinet Connection13
Pin Assignment Profibus-DP13
Pin Assignment Profinet13
Mechanical Installation14
Mounting14
Mounting Optical Fiber / Optics (Only Devices with Optical Fiber)14
Bending Radius Optical Fiber14
Winding and Unwinding the Optical Fiber14
Mounting of Optical Fiber14
Connect the Optics15
Ambient Temperature15
Alignment Onto the Measuring Object16
Alignment with the Laser Targeting Light16
Alignment with the through Lens Sighting / View Finder17
Alignment with the Camera Module (Only M3)17
Setting the Measuring / Focus Distance18
Manually Focusable Optics18
Motorized Focus Optics (Only M3)18
Manually Focusable Fiber Optic Lenses18
Fixed Focus Optics (Only M3)18
Spot Size Tables19
Manually Adjusted or Motorized Focus Optics with Laser Targeting Light or View Finder19
Manually Adjustable or Motorized Focus Optics with Camera Module20
Manually Adjustable or Motorized Focus Optics Model M31320
Manually Adjusted or Motorized Focus Optics Model M32321
Focusable Fiber-Optic Lenses22
Fixed Focus Optics22
Calculation of the Spot Size Diameter Outside the Focused Distance23
Configuring the Pyrometer23
Displays on the Device23
Key Functions24
Parameters / Settings25
Response Time T26
Dynamic Adaptation at Low Signal Levels (Only M3 Devices)26
Storage Mode Maximum Value Storage (Peak Picker) / Clear Time T26
Emissivity Ɛ26
Transmittance27
Spot Size Fill Factor27
Temperature Sub Range28
Temperature Unit28
Analog Output28
Test Current28
Upscale-Burnout (Only Via Software Sensortools)28
Customize Analog Output (Only Via Software Sensortools)29
Interface Type (Only M3 Devices)29
Baud Rate29
Address29
Interface Delay / Answer Delay)29
Key Lock29
Sensortools Software30
Program Start / Connecting the Pyrometer30
Software Windows32
Main Window  Graphs32
Control Window35
Device Settings and Configuration37
Configurable Inputs / Outputs38
Service Functions40
Interface40
Data Collection (Buffer Mode)41
Single-Point Adjustment42
PID Controller Equipment44
Profibus- / Profinet Equipment46
Fieldbus Mode Selection for Reading the Pyrometer Data46
Writing Pyrometer Data48
Setups49
Data Playback50
Communication / Options51
Spot Size Calculator51
Sensorflash Software (Update Firmware)52
Technical Data53
Storage54
Dimensions55
Composition of the Type Number56
Accessories57
Maintenance58
Cleaning58
Change Protection Window / Lens at Manual Focusable Optics58
Pyrometer Calibration59
Trouble-Shooting59
Communication Via Serial Interface / Interface Commands59
Index64

SensorTherm METIS H3 series - Page 66

Table of Contents

Related product manuals