Shark 100 - Page 53

To Next Page

To Previous Page

Doc# E145701 3 - 3

3: Mechanical Installation

Electro Industries/GaugeTech

The Leader In Power Monitoring and Smart Grid Solutions

Electro Industries/GaugeTech

The Leader In Power Monitoring and Smart Grid Solutions

Figure 3.5: ANSI Mounting Cutout

Figure 3.6: DIN Mounting Cutout

3Q

8v

v

$IAMETER

#UTOUT

CM



CM

Main Page

Product Warranty5
Use of Product for Protection6
Statement of Calibration6
Disclaimer6
Table of Contents9
1: Three-Phase Power Measurement15
Three-Phase System Configurations15
1: Wye Connection15
2: Delta Connection18
3: Blondel's Theorem and Three Phase Measurement20
Power, Energy and Demand22
Reactive Energy and Power Factor26
Harmonic Distortion28
Power Quality31
2: Meter Overview and Specifications33
Hardware Overview33
1: Voltage and Current Inputs35
2: Model Number Plus Option Numbers36
Technology38
4: Measured Values40
5: Utility Peak Demand41
Specifications41
Compliance47
Accuracy48
3: Mechanical Installation51
Introduction51
ANSI Installation Steps54
DIN Installation Steps55
Shark® 100T Transducer Installation56
4: Electrical Installation59
Considerations When Installing Meters59
CT Leads Terminated to Meter62
CT Leads Pass through (no Meter Termination)63
Quick Connect Crimp-On Terminations64
Voltage and Power Supply Connections65
Ground Connections65
Voltage Fuses65
Electrical Connection Diagrams66
Extended Surge Protection for Substation Instrumentation79
5: Communication Installation81
2: RS485/KYZ Output Com 2 (485P Option)81
1: Using the Unicom 250085
Electro Industries/Gaugetech Doc TOC86
Configuring the Shark® 100 - INP1086
1: Setting up the Host PC to Communicate with the Shark® 100 - INP10 Meter87
1: Configuring the Host Pc's Ethernet Adapter through87
Windows87
2: Setting up the Shark® 100 - INP10 Meter for Ethernet Communication89
1: Configuring the Shark® 100 - INP10 Meter's90
2: Resetting the Ethernet Card (INP10)92
Shark® 100B Meter Ethernet Configuration92
6: Using the Shark® 100/50 Meter93
Programming the Shark® 100/100B/50 Meter Using the Faceplate93
1: Understanding Meter Face Elements93
2: Understanding Meter Face Buttons94
Using the Front Panel95
1: Understanding Startup and Default Displays95
2: Using the Main Menu96
3: Using Reset Mode97
4: Entering a Password98
5: Using Configuration Mode99
1: Configuring the Scroll Feature101
2: Configuring CT Setting102
Electro Industries/Gaugetech Doc TOC102
3: Configuring PT Setting103
4: Configuring Connection Setting105
5: Configuring Communication Port Setting105
6: Using Operating Mode107
Understanding the % of Load Bar108
Performing Watt-Hour Accuracy Testing (Verification)109
Programming the Transducer or Meter Using Software111
1: Accessing the Transducer/Meter in Default111
2: Connecting to the Transducer/Meter through112
TM Software112
Irda Port (Com 1)115
3: Device Profile Settings116
Display Configuration120
7: Using the Shark® 100B Meter125
Introduction125
1: about Bacnet125
Shark® 100B Meter's Bacnet Objects126
Configuring the Shark® 100B Meter129
Using the Shark® 100B Meter's Web Interface136
Using the Shark® 100B in a Bacnet Application142
A: Shark® 100/50 Meter Navigation Maps143
A.1: Introduction143
A.2: Navigation Maps (Sheets 1 to 4)143
B: Shark® 100 and 50 Meter Modbus Map149
B.1: Introduction149
B.2: Modbus Register Map Sections149
B.3: Data Formats149
B.4: Floating Point Values150
B.5: Modbus Register Map151
C: Shark® 100 Meter DNP Map169
C.1: Introduction169
C.2: DNP Mapping (DNP-1 to DNP-2169
D: DNP 3.0 Protocol Assignments173
D.1: DNP Implementation173
D.2: Data Link Layer174
D.3: Transport Layer175
D.4: Application Layer175
D.4.1: Object and Variation176
D.4.1.1: Binary Output Status (Obj. 10, Var. 2177
D.4.1.2: Control Relay Output Block (Obj. 12, Var. 1178
D.4.1.3: 32-Bit Binary Counter Without Flag (Obj. 20, Var. 5179
D.4.1.4: 16-Bit Analog Input Without Flag (Obj. 30, Var. 4179
D.4.1.5: Class 0 Data (Obj. 60, Var. 1185
D.4.1.6: Internal Indications (Obj. 80, Var. 1185
E: Using the USB to Irda Adapter CAB6490187
E.1: Introduction187
E.2: Installation Procedures187

Shark 100 - Page 53

Table of Contents

Related product manuals