AR-M256/M257/M258/M316/M317/M318/5625/5631 SIMULATION 8 - 50
Note: Executable only when the FAX is installed.
Operation/procedure
Select the signal number with the 10-key, and press the [START] key.
By setting the signal number, signals are sent to the line and the
machine speaker. (Sending signals is continued until interruption com-
mand is made (by pressing [CUSTOM SETTINGS] key.)
By entering the signal number and pressing the [START] key during
execution, the signal kind can be changed.
Note: Executable only when the FAX is installed.
5 26.4 V34 – –
6 24.0 V34 – –
7 16.0 V34 – –
8 19.2 V34 – –
9 16.8 V34 – –
10 14.4 V34 – –
11 12.0 V34 – –
12 9.6 V34 – –
13 7.2 V34 – –
14 4.8 V34 – –
15 2.4 V34 – –
16 14.4 V33 – –
17 12.0 V33 – –
18 14.4 V17 – –
19 12.0 V17 – –
20 9.6 V17 – –
21 7.2 V17 – –
22 9.6 V29 – –
23 7.2 V29 – –
24 4.8 V27t – –
25 2.4 V27t – –
26 0.3 FLG 7EH Flag signal Yes
27 CED2100
Tone signal Yes
28 CNG1100
29 0.3 V21
30 ANSam
31 RINGER
Pseudo-ringer sound
([ON HOOK] key ON)
None
32 No MSG
Voice message (no sound)
None
Under the state where the ring back
tone can be sent to the line, keep the
sound composition IC volume to 0.
33 No RBT
Ring back tone (no sound)
None
Under the state where the ring back
tone can be sent to the line, keep the
G/A volume to 0.
34 DP MAKE
Dial pulse (make)
1: 0dB
2: Soft SW
Maintain the make state with keeping
the condition to be able to send to the
dial pulse line.
35 DP BRK
Dial pulse (break)
1: 0dB
2: Soft SW
Maintain the break state with keeping
the condition to be able to send to the
dial pulse line.
Item Send signal
Send level
Selection
menu
1
66-5
Purpose Operation test/check
Function
(Purpose)
Signal send mode (Signal send level soft SW setting)
Section FAX
Item Operation
Signal number Send signal
Send level
Selection
menu
1 NO SIGNAL Signal not sent None
2 33.6 V34 33.6 V34 –
3 31.2 V34 31.2 V34 –
4 28.8 V34 28.8 V34 –
5 26.4 V34 26.4 V34 –
6 24.0 V34 24.0 V34 –
7 16.0 V34 16.0 V34 –
8 19.2 V34 19.2 V34 –
9 16.8 V34 16.8 V34 –
10 14.4 V34 14.4 V34 –
11 12.0 V34 12.0 V34 –
12 9.6 V34 9.6 V34 –
13 7.2 V34 7.2 V34 –
14 4.8 V34 4.8 V34 –
15 2.4 V34 2.4 V34 –
16 14.4 V33 14.4 V33 –
17 12.0 V33 12.0 V33 –
18 14.4 V17 14.4 V17 –
19 12.0 V17 12.0 V17 –
20 9.6 V17 9.6 V17 –
21 7.2 V17 7.2 V17 –
22 9.6 V29 9.6 V29 –
23 7.2 V29 7.2 V29 –
24 4.8 V27t 4.8 V27t –
25 2.4 V27t 2.4 V27t –
26 0.3 FLG 7EH Flag signal Yes
27 CED2100
Tone signal Yes
28 CNG1100
29 0.3 V21
30 ANSam
31 RINGER
Pseudo-ringer sound
([ON HOOK] key ON)
None
32 No MSG
Voice message (no sound)
None
Under the state where the ring back
tone can be sent to the line, keep the
sound composition IC volume to 0.
33 No RBT
Ring back tone (no sound)
None
Under the state where the ring back
tone can be sent to the line, keep the
G/A volume to 0.
34 DP MAKE
Dial pulse (make)
1: 0dB
2: Soft SW
Maintain the make state with keeping
the condition to be able to send to the
dial pulse line.
35 DP BRK
Dial pulse (break)
1: 0dB
2: Soft SW
Maintain the break state with keeping
the condition to be able to send to the
dial pulse line.
To Next Page
Loading...
