Sharp MX-5001N - Page 221

MX-5001N SIMULATION 6 – 74
[50-sheet machine]
44-37
Purpose
Adjustment/Setup
Function (Purpose)
Used to set the development bias correc-
tion level in the continuous printing opera-
tion.
Section
Operation/Procedure
1) Select a set target color with the touch panel.
2) Select a target item with [↑] [↓] buttons.
3) Enter the set value with 10-key.
4) Press [OK] key. (The set value is saved.)
NOTE:
When the print density is varied in the continuous printing opera-
tion, this simulation is used.
C PAPER MFT Tray selection Manual paper feed 1 1 - 6 3
(CS2)
CS1 Main unit 1 stage 2
CS2 Main unit 2 stage 3
CS3 Option paper feed desk 1 stage 4
CS4 Option paper feed desk 2 stage 5
LCC LCC 6
Item/Display Content Setting range
Default
value
1
Item/Display Content Setting range
Default
value
A PRINT MODE 45deg Print mode 45
degrees
Deflection check pattern print for every 45 degrees (8-sheet
print)
(1)0° (2)45° (3)90°(4)135° (5)180° (6)225° (7)270° (8)315°
* The number in () is printed on the output pattern.
11 - 3 3
(SET
VALUE)
90deg 90
degrees
Deflection check pattern print for every 90 degrees (4-sheet
print)
(1)0° (2)90° (3)180° (4)270°
* The number in () is printed on the output pattern.
2
SET
VALUE
SET
VALUE
Deflection check pattern print at the set value (1-sheet print) 3
B PHASE(C) C tandem phase setting
The phase of C is
changed by 45° each time
in the range of 0 - 315°.
Angle step 0° (1) → 45° (2) → 90° (3) → 135° (4) → 180° (5) →
225° (6) → 270° (7) → 315° (8)
1 - 8 2
C PHASE(M) M tandem phase setting
The phase of M is
changed by 45° each time
in the range of 0 - 315°.
Angle step 0° (1) → 45° (2) → 90°
(3) → 135° (4) → 180° (5) →
225° (6) → 270° (7) → 315° (8)
1 - 8 4
D PHASE(Y) Y tandem phase setting
The phase of Y is
changed by 45° each time
in the range of 0 - 315°.
Angle step 0° (1) → 45° (2) → 90° (3) → 135° (4) → 180° (5) →
225° (6) → 270° (7) → 315° (8)
1 - 8 5
E PAPER MFT Tray selection Manual paper feed 1 1 - 6 3
(CS2)
CS1 Main unit 1 stage 2
CS2 Main unit 2 stage 3
CS3 Option paper feed desk 1 stage 4
CS4 Option paper feed desk 2 stage 5
LCC LCC 6
ǂǂǂ6,08/$7,21ǂǂ12
&/26(
7(67
'580326,7,216(77,1*



$˖
˷˹
˹
˖35,1702'(6(79$/8($˖
˖3+$6(&
%˖
˖3+$6(0
&˖
˖3+$6(<
'˖
˖3$3(5&6(˖
2.
(;(&87(
: Oct. 24 2008
1