Sharp MX-5001N - Page 86

MX-5001N ADJUSTMENTS 5 – 44
2) Set the adjustment chart to the RSPF/DSPF.
3) Make a duplex copy in the normal magnification ratio from the
manual paper feed tray, and check the image position on the
front surface and the back surface of the copy paper.
If the difference is within the range of 0 ± 2.7mmm there is no
need to perform the adjustment.
If the adjustment is required, perform the following procedures.
4) Enter the SIM50-12 and 50-6 mode.
SIM50-12
A - C: When the adjustment value is increased, the image
position is shifted to the rear frame side.
1step = 0.1mm
SIM50-6
(DSPF)
(RSPF)
Item Display Content
Setting
range
Default
value
A OC Document table image off-
center adjustment
1 - 99 50
B SPF(SIDE1) SPF front surface image off-
center adjustment
1 - 99 50
C SPF(SIDE2) SPF back surface image off-
center adjustment
1 - 99 50
original copy
a
b
ǂǂǂ6,08/$7,21ǂǂ12
&/26(
7(67
25,*,1$/&(17(52))6(76(783



$˖
˷ ˹
˖2&
$˖
˖63)6,'(
%˖
˖63)6,'(
&˖
2.
(SIM50-12)
ǂǂǂ6,08/$7,21ǂǂ12
&/26(
7(67
/($'('*($'-8670(179$/8(63)

$˖
˷˹
˖6,'(
$˖
˖6,'(
%˖
˖/($'B('*(6,'(
&˖
˖)5217B5($56,'(
'˖
˖/($'B('*(6,'(
)˖
˖75$,/B('*(6,'(
(˖
˖)5217B5($56,'(
*˖
˖75$,/B('*(6,'(
+˖
˖2)6(7B63)
,˖
˖2)6(7B63)
-˖
˖6&$1B63(('B63)
.˖
2.


(SIM50-6)
Item Display Content
Setting
range
Default
value
A SIDE1 Front surface
document scan
position
adjustment
(CCD)
1 - 99 50
B SIDE2 Back surface
document scan
position
adjustment
(CCD)
1 - 99 50
CImage
loss
amount
setting
SIDE1
LEAD_EDGE
(SIDE1)
Front surface
lead edge image
loss amount
setting
0 - 99 20
D FRONT_REAR
(SIDE1)
Front surface
side image loss
amount setting
0 - 99 20
E TRAIL_EDGE
(SIDE1)
Front surface
rear edge image
loss amount
setting
0 - 99 30
FImage
loss
amount
setting
SIDE2
LEAD_EDGE
(SIDE2)
Back surface
lead edge image
loss amount
setting
0 - 99 30
G FRONT_REAR
(SIDE2)
Back surface
side image loss
amount setting
0 - 99 20
H TRAIL_EDGE
(SIDE2)
Back surface
rear edge image
loss amount
setting
0 - 99 20
I OFSET_SPF1 DSPF front
surface
document off-
center
adjustment
1 - 99 50
J OFSET_SPF2 DSPF back
surface
document off-
center
adjustment
1 - 99 50
K SCAN_SPEED_SPF1 DSPF document
front surface
magnification
ratio adjustment
(Sub scan)
1 - 99 50
Item Display Content
Setting
range
Default
value
A SIDE1 Front surface
document scan
position
adjustment
(CCD)
1 - 99 50
B SIDE2 Back surface
document scan
position
adjustment
(CCD)
1 - 99 50
CImage
loss
amount
setting
SIDE1
LEAD_EDGE
(SIDE1)
Front surface
lead edge image
loss amount
setting
0 - 99 20
D FRONT_REAR
(SIDE1)
Front surface
side image loss
amount setting
0 - 99 20
E TRAIL_EDGE
(SIDE1)
Front surface
rear edge image
loss amount
setting
0 - 99 30