Siemens POL638 Series

To Next Page

To Previous Page

94 / 244

Siemens Standard application AHU CE1P3977en_02

Building Technologies Functions 01.02.2010

Parameter Range Function

State

– Active – Pending error on module 2.

Cause of error.

Basis Document Siemens Climatix Control System

BDCX.100820.01GB

Page 94

Main Page

Default Chapter3
- Table of Contents3
1 About this Document7
- Revision History7
- Referenced Documents7
- Before You Start7
2 Philosophy of Air Handling Units9
- Overview9
- Properties9
- Safety10
- Packing, Transport and Storage11
- Maintenance and Service11
- Environmental Protection and Waste Management11
- Abbreviations11
3 Function Overview12
- General12
- Diagram Standard AHU13
- Workflow Diagram14
4 Hardware Overview15
- Basic Controller (Pol638X)15
- Extension Module (POL955)18
- Inbuild HMI20
- External HMI (DM)20
- Room Unit25
5 Functions33
- Global Functions33
- Operating Mode35
- Damper Control46
- Fan Control50
- Temperature Control59
- Heat Recovery Damper67
- Heat Recovery (Plate, Wheel, Water)69
- Heating / Heating 273
- Electrical Heating / Electrical Heating 277
- Cooling / Cooling 279
- Humidity Control83
- Air Quality Control90
- Auxiliary Functions91
- Alarm Handling (Alarm Outputs)93
6 Detail Pages: Inputs and Outputs95
- General95
- Analog Outputs95
- Digital Outputs98
- Multistate Outputs100
- Analog Inputs102
- Digital Inputs106
7 Detail Pages: Controller110
- Loop Controller110
- Cascade Controller111
8 Detail Pages: Time Switch Program114
- General114
- Week Scheduler114
- Day Scheduler115
- Calendar (Exception and Fixed Off)115
9 Communication118
- General118
- Modbus119
- Lon124
- Bacnet128
- Room Units131
10 Application Info135
11 Save / Restore Parameters136
12 Onboard WEB Functionalities139
13 System Settings141
- Password Settings141
- Change Passwords141
- Language Support142
- Target142
- Daylight Saving Time143
- HMI (Operating Unit)145
- Diagnostics145
- Diag Object Handler146
14 SD Card and Modem148
- SD Card Functions (Update Application)148
- Modem / SMS149
15 Configuration152
- Configuration 1154
- Configuration 2159
- Configuration I/Os167
- Check Config I/Os176
16 Examples177
17 Hmi177
- Overview177
- Start Page177
- Main Index177
- Main Overview178
- Configuration178
- Configuration 1178
- Configuration 2180
- Configuration I/Os184
- Check Config I/Os188
- 17.10 Global Functions189
- 17.11 Inputs189
- 17.12 Operating Mode191
- 17.13 Damper Control194
- 17.14 Fan Control195
- 17.15 Temperature Control197
- 17.16 Humidity Control206
- 17.17 Air Qualtity Control208
- 17.18 Auxiliary209
- 17.19 Loop Controllers209
- 17.20 Operation Hours210
- Alarm Handling (Alarm Outputs)211
- 17.22 Outputs212
18 Time Scheduler213
- Week Schedulers213
- Detail Pages: Analog Outputs214
- Detail Pages: Digital Outputs215
- Detail Pages: Multistate Outputs216
- Detail Pages: Analog Inputs217
- Detail Pages: Digital Inputs219
19 Alarming222
- General222
- Alarm List Detail223
- Alarm List224
- Alarm History224
- Alarm List / History Settings225
- Alarm Lists226
20 Appendices230
- Point Tables230
- Diagnostic Tables for Check I/O232
- Navigation Illustrations235
- Parameter List Room Unit239
Index241

Siemens POL638 Series

Table of Contents

Related product manuals