EasyManua.ls Logo

Siemens Simatic S7-400 - Page 110

Siemens Simatic S7-400
136 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Loading...
Programming the OPC UA client blocks
5.10 Error numbers
CP 443-1 OPC UA
110 Operating Instructions, 01/2017, C79000-G8976-C427-02
Done
Error
ErrorID (hex)
Name
Meaning
0 1 00A30000 GoodEntryReplaced The data or event field was successfully replaced in the his-
torical database.
0 1 00A50000 GoodNoData No data exists for the requested time range or event filter.
0 1 00A60000 GoodMoreData The data or event field was successfully replaced in the his-
torical database.
0
1
00A70000
GoodCommunicationEvent
The communication layer has raised an event.
0
1
00A80000
GoodShutdownEvent
The system is shutting down.
0
1
00A90000
GoodCallAgain
The operation is not finished and needs to be called again.
0
1
00AA0000
GoodNonCriticalTimeout
A non-critical timeout occurred.
0 1 00BA0000 GoodResultsMayBe
Incomplete
The server should have followed a reference to a node in a
remote server but did not. The result set may be incomplete.
0 1 406C0000 UncertainReferenceOutOf
Server
One of the references to follow in the relative path references
to a node in the address space in another server.
0 1 408F0000 UncertainNoCommunication
LastUsableValue
Communication to the data source has failed. The variable
value is the last value that had a good quality.
0
1
40900000
UncertainLastUsableValue
Whatever was updating this value has stopped doing so.
0 1 40910000 UncertainSubstituteValue The value is an operational value that was manually overwrit-
ten.
0 1 40920000 UncertainInitialValue The value is an initial value for a variable that normally re-
ceives its value from another variable.
0
1
40930000
UncertainSensorNotAccurate
The value is at one of the sensor limits.
0 1 40940000 UncertainEngineeringUnits
Exceeded
The value is outside of the range of values defined for this
parameter.
0 1 40950000 UncertainSubNormal The value is derived from multiple sources and has less than
the required number of Good sources.
0 1 40A40000 UncertainDataSubNormal The value is derived from multiple values and has less than
the required number of Good values.
0 1 40BC0000 UncertainReferenceNot
Deleted
The server was not able to delete all target references.
0 1 40C00000 UncertainNotAllNodes
Available
The list of references may not be complete because the un-
derlying system is not available.
0
1
80010000
BadUnexpectedError
An unexpected error occurred
0 1 80020000 BadInternalError An internal error occurred as a result of a programming or
configuration error.
0
1
80030000
BadOutOfMemory
Not enough memory to complete the operation.
0
1
80040000
BadResourceUnavailable
An operating system resource is not available
0
1
80050000
BadCommunicationError
A low level communication error occurred.
0 1 80060000 BadEncodingError Encoding halted because of invalid data in the objects being
serialized.
0
1
80070000
BadDecodingError
Decoding halted because of invalid data in the stream.
0 1 80080000 BadEncodingLimits-
Exceeded
The message encoding/decoding limits imposed by the stack
have been exceeded.
0 1 80B80000 BadRequestTooLarge The resources (memory) of the CPU are temporarily occu-
pied
0
1
80B90000
BadResponseTooLarge
The response message size exceeds limits set by the client.
0
1
80B90000
BadUnknownResponse
An unrecognized response was received from the server.

Table of Contents

Other manuals for Siemens Simatic S7-400

Related product manuals