Siemens SINAMICS V20 - Page 25

SINAMICS V20 Inverter
A5E37281078-003, 05/2016
25
Parameter
Description
Range
Factory default
Acc.
level
P0640[0...2]
Motor overload factor [%]
10.0 - 400.0
150.0
2
P0700[0...2]
Selection of command source
0 - 5
1
1
0
Factory default setting
2
Terminal
1
Operator panel (keypad)
5
USS / MODBUS on RS485
P0701[0...2]
Function of digital input 1
0 - 99
0
2
0
Digital input disabled
15
Fixed frequency selector bit0
1
ON / OFF1
16
Fixed frequency selector bit1
2
ON reverse / OFF1
17
Fixed frequency selector bit2
3
OFF2 - coast to standstill
18
Fixed frequency selector bit3
4
OFF3 - quick ramp-down
22
QuickStop Source 1
5
ON / OFF2
23
QuickStop Source 2
9
Fault acknowledge
24
QuickStop Override
10
JOG right
25
DC brake enable
11
JOG left
27
Enable PID
12
Reverse
29
External trip
13
MOP up (increase frequency)
33
Disable additional freq setpoint
14
MOP down (decrease frequency)
99
Enable BICO parameterization
P0702[0...2]
Function of digital input 2
0 - 99
0
2
P0703[0...2]
Function of digital input 3
0 - 99
9
2
P0704[0...2]
Function of digital input 4
0 - 99
15
2
P0712 [0...2]
Analog / digital input 1
0 - 99
0
2
P0713[0...2]
Analog / digital input 2
0 - 99
0
2
P0717
Connection macro
0 - 255
0
1
r0722.0...12
CO / BO: Digital input values
-
-
2
P0727[0...2]
Selection of 2 / 3-wire method
0 - 3
0
2
0
Siemens (start / dir)
2
3-wire (fwd / rev)
1
2-wire (fwd / rev)
3
3-wire (start / dir)
P0731[0...2]
BI: Function of digital output 1
0 - 4294967295
52.3
2
P0732[0...2]
BI: Function of digital output 2
0 - 4294967295
52.7
2
r0752[0...1]
Actual analog input [V] or [mA]
-
-
2
r0754[0...1]
Actual analog input value after scaling [%]
-
-
2
r0755[0...1] CO: Actual analog input after scaling
[4000h]
- - 2
P0756[0...1]
Type of analog input
0 - 4
0
2
0
Unipolar voltage input (0 to +10 V)
1
Unipolar voltage input with monitoring (0 to 10 V)
2
Unipolar current input (0 to 20 mA)
3
Unipolar current input with monitoring (0 to 20 mA)
4
Bipolar voltage input (-10 V to +10 V)
P0757[0...1]
Value x1 of analog input scaling
-20 - 20
0
2
P0758[0...1]
Value y1 of analog input scaling [%]
-99999.9 - 99999.9
0.0
2
P0759[0...1]
Value x2 of analog input scaling
-20 - 20
10
2
P0760[0...1]
Value y2 of analog input scaling [%]
-99999.9 - 99999.9
100.0
2
P0761[0...1]
Width of analog input deadband
0 - 20
0
2
P0771[0]
CI: Analog output
0 - 4294967295
21[0]
2
P0773[0]
Smooth time analog output [ms]
0 - 1000
2
2
r0774[0]
Actual analog output value [V] or [mA]
-
-
2
P0775[0]
Permit absolute value
0 - 1
0
2
P0777[0]
Value x1 of analog output scaling [%]
-99999 - 99999
0.0
2
P0778[0]
Value y1 of analog output scaling
0 - 20
0
2