14 Support for errors and faults
14.1 Error/fault code list
Code no. Cause of error/fault Described in Section
10 Outside temp sensor error See 5.6.5 "Outside temperature"
11 >1 outside temperature sensor See 5.6.5 "Outside temperature"
12 Outs sensor simulation active See 5.6.5 "Outside temperature"
100 Simulation inputs active See 5.1.2 "Universal inputs"
101...264 [N.X1] sensor error …
RMZ788(2).X4 sensor error
See 5.2.6 "Analog inputs"
See 5.5.5 "Remote setpoint adjuster,
absolute"
See 5.6.5 "Outside temperature"
1310 [Motor 1] fault See 8.4.4 "Motor"
1311 [Motor 1] overload See 8.4.7 "Motor"
1312 [Motor 1] no flow See 8.4.6 "Motor"
1314 [Motor 1A] overload See 8.4.7 "Motor"
1315 [Motor 1B] overload See 8.4.7 "Motor"
1316 [Motor 1A] no flow See 8.4.6 "Motor"
1317 [Motor 1B] no flow See 8.4.6 "Motor"
1318 [Mot 1] precom no checkb signal See 8.4.9 "Motor"
1360 [Motor 6] fault See 8.4.4 "Motor"
1361 [Motor 6] overload See 8.4.7 "Motor"
1362 [Motor 6] no flow See 8.4.6 "Motor"
1364 [Motor 6A] overload See 8.4.7 "Motor"
1365 [Motor 6B] overload See 8.4.7 "Motor"
1366 [Motor 6A] no flow See 8.4.6 "Motor"
1367 [Motor 6B] no flow See 8.4.6 "Motor"
1368 [Mot 6] precom no checkb signal See 8.4.9 "Motor"
1911 [O'hrs 1] serv req See 6.3.4 "Operating hours“
1912 [O'hrs 2] serv req See 6.3.4 "Operating hours“
1913 [O'hrs 3] serv req See 6.3.4 "Operating hours“
1914 [O'hrs 4] serv req See 6.3.4 "Operating hours“
3011 [Main contr var 1] sensor error See 11.2.2 "Universal controller"
3012 [Main contr var 2] sensor error See 11.2.2 "Universal controller"
3013 [Main contr var 3] sensor error See 11.2.2 "Universal controller"
5000 No bus power supply See 13.2.6 "Communications"
5001 System time failure See 4.1.3 "Date and time"
5002 >1 clock time master See 4.1.3 "Date and time"
5003 Invalid time of day See 4.1.3 "Date and time"
5101 [Time switch 1] failure See 7.1.5 "Time switch"
… … …
5151 [Time switch 6] failure See 7.1.5 "Time switch"
5201 Hol/spec day program failure See 7.2.6 "Holidays/special days"
5202 >1 hol/spec day program See 7.2.6 "Holidays/special days"
5801 H/C changeover signal failure See 10.4.12 "H/C changeover"
5802 >1 heat/cool changeover signal See 10.4.12 "H/C changeover"
5902 >1 identical LTE zone See 13.2.6 "Communications"
6001 >1 identical device address See 13.2.6 "Communications"
191 / 216
Siemens Switching and monitoring device RMS705B CE1P3124en
Building Technologies Support for errors and faults 01.04.2010
To Next Page
Loading...
