EasyManua.ls Logo

SMC Networks SMCGS24C-Smart User Manual

SMC Networks SMCGS24C-Smart
122 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #13 background image
C
OMPLIANCES
ix
Warnings and Cautionary Messages
Warnings (in German)
Environmental Statement
The manufacturer of this product endeavours to sustain an environmentally-friendly policy
throughout the entire production process. This is achieved though the following means:
Adherence to national legislation and regulations on environmental production standards.
Conservation of operational resources.
Waste reduction and safe disposal of all harmful un-recyclable by-products.
Recycling of all reusable waste content.
Design of products to maximize recyclables at the end of the product’s life span.
Continual monitoring of safety standards.
Warning: This product does not contain any serviceable user parts.
Warning: Installation and removal of the unit must be carried out by qualified personnel
only.
Warning: When connecting this device to a power outlet, connect the field ground lead
on the tri-pole power plug to a valid earth ground line to prevent electrical
hazards.
Warning: This switch uses lasers to transmit signals over fiber optic cable. The lasers are
compliant with the requirements of a Class 1 Laser Product and are inherently
eye safe in normal operation. However, you should never look directly at a
transmit port when it is powered on.
Caution: Wear an anti-static wrist strap or take other suitable measures to prevent
electrostatic discharge when handling this equipment.
Caution: Do not plug a phone jack connector in the RJ-45 port. This may damage this
device. Les raccordeurs ne sont pas utilisé pour le système téléphonique!
Caution: Use only twisted-pair cables with RJ-45 connectors that conform to FCC
standards.
Achtung: Dieses Produkt enthält keine Teile, die eine Wartung vom Benutzer benötigen.
Achtung: Installation und Deinstallation des Gerätes müssen von qualifiziertem
Servicepersonal durchgeführt werden.
Achtung: Wenn das Gerät an eine Steckdose angeschlossen wird, muß der Masseanschluß
am dreipoligen Netzstecker mit Schutzerde verbunden werden, um elektrische
Gefahren zu vermeiden.
Achtung: Dieses Gerät nutzt Laser zur Signalübertragung über Glasfasern. Die Laser
entsprechen den Anforderungen an eine Lasereinrichtung der Klasse 1 und sind
durch ihre Bauart im normalen Betrieb sicher für die Augen. Trotzdem sollte
niemals direkt in den einen Übertragungskanal geblickt werden, wenn er
eingeschaltet ist.

Table of Contents

Questions and Answers:

SMC Networks SMCGS24C-Smart Specifications

General IconGeneral
Ports24
LayerLayer 2
Switching Capacity48 Gbps
MAC Address Table8K
Forwarding Rate35.7 Mpps
Jumbo Frame SupportYes
Packet Buffer Memory512 KB
Operating Humidity10% to 90% (non-condensing)
Storage Humidity5% to 90% (non-condensing)
Power Consumption20W
Jumbo Frame Size9216 Bytes
ManagementWeb-based management
FeaturesQoS, VLAN, IGMP Snooping, Port Mirroring
Storage Temperature-40°C to 70°C

Summary

Limited Warranty

Warranty Exclusions and Limitations

Details the exclusive warranties and limitations of SMC product warranties.

Limitation of Liability

Outlines the limitations of SMC's liability for damages related to product use.

Compliances

CE Mark Declaration of Conformance

Declaration of conformity with EU directives for EMI and safety.

Safety and Power Cord Compliance

Covers general safety, fiber optic port, and power cord requirements.

Chapter 3 Installing the Switch

Site Selection Guidelines

Provides guidelines for choosing a suitable location for switch installation.

Chapter 5 Configuring the Switch

Configuring via Web Interface

Guides on accessing and using the switch's web-based management interface.

Setting Switch IP Address

Details manual configuration of IP address, subnet mask, and default gateway.

Configuring Logon Password

Instructs on changing the administrator password for secure access.

Port Configuration

Enables manual setting of port speed, duplex mode, and flow control.

Configuring Rate Limits

Controls maximum traffic rate on interfaces to limit traffic in/out of the switch.

Cable Diagnostic

Performs cable diagnostics to diagnose faults like shorts or opens.

Trunks Membership and Configuration

Allows creation and configuration of up to eight trunks for port aggregation.

VLAN Settings

Guides on configuring VLAN behavior, membership, and frame types.

QoS Settings

Enables prioritization of network traffic based on QoS modes like 802.1p or DSCP.

IP Filter Configuration

Sets up source IP filters to block unwanted access or provide specific access.

Appendix A Troubleshooting

Troubleshooting Switch Indicators

Provides a chart to diagnose issues based on Power and Link LED status.

Power and Cooling Problems

Addresses issues related to power indicators, unit overheating, and fan operation.

Appendix B Cables

Twisted-Pair Cable and Pin Assignments

Details pin assignments for 10/100BASE-TX and 1000BASE-T connections.

Related product manuals