Need help?Do you have a question about the socomec MASTERYS GP4 Series and is the answer not in the manual?
General| Series | MASTERYS GP4 |
|---|---|
| Type | Online double conversion UPS |
| Frequency | 50/60 Hz |
| Cooling | Forced air |
| Protection Degree | IP20 |
| Input Voltage | 3 x 400 V ± 10% |
| Battery Type | VRLA |
| Communication Interface | RS232, USB |
| Operating Temperature | 0 to 40 °C |
| Storage Temperature | -25 to 70 °C |
| Relative Humidity | 0 to 95% (non-condensing) |
| Dimensions | Varies depending on power rating |
| Weight | Varies depending on power rating |
| Standards | IEC 62040-1, IEC 62040-2 |
Details the procedure for installing the RTU card, including slot selection and fixing methods.
Explains the installation process for the MODBUS TCP card in the appropriate slot.
Covers default serial connection parameters and auto baud rate procedures.
Describes the features of the IDA interface and the meaning of its LED indicators.
Presents a generic table mapping Modbus addresses to UPS data points, including types and access methods.
Explains the modular unit structure and how MODBUS accesses UPS and module data.
Provides a mapping for accessing module data within the Modulys GP system.
Details UPS configuration parameters for Modulys GP, including installation code and device type.
Defines the configuration settings for individual units within the Modulys GP system.
Lists reference information for Modulys GP UPS, such as serial numbers and device locations.
Describes the status bits for Modulys GP UPS, covering output, functioning, and device states.
Details additional programmable status bits for Modulys GP UPS, used for custom inputs/outputs.
Summarizes the operational status of individual modules within the Modulys GP system.
Lists critical alarms for Modulys GP UPS, categorized by load, mode, service, battery, and rectifier.
Covers additional programmable alarm bits for Modulys GP UPS, enabling custom event monitoring.
Provides a synthesized view of general alarms for each module in the Modulys GP system.
Details UPS measurements for Modulys GP, including load, voltage, current, and temperature readings.
Defines commands available for Modulys GP UPS, such as eco mode control and reset functions.
Specifies the format for reading and writing UPS clock and date information for Modulys GP.
Details UPS configuration parameters for ITYS PRO, including installation code and device type.
Lists reference information for ITYS PRO UPS, such as serial numbers and device locations.
Describes the status bits for ITYS PRO UPS, covering output, functioning, and device states.
Details additional programmable status bits for ITYS PRO UPS, used for custom inputs/outputs.
Lists critical alarms for ITYS PRO UPS, categorized by load, mode, service, battery, and rectifier.
Covers additional programmable alarm bits for ITYS PRO UPS, enabling custom event monitoring.
Details UPS measurements for ITYS PRO, including load, voltage, current, and temperature readings.
Defines commands available for ITYS PRO UPS, such as eco mode control and reset functions.
Specifies the format for reading and writing UPS clock and date information for ITYS PRO.
Illustrates the architecture of Masterys BC+ and GP4 UPS units and systems.
Explains how to access unit data for Masterys BC+ and GP4 UPS, including single and parallel systems.
Details UPS configuration parameters for Masterys BC+ and GP4, including installation code and device type.
Lists reference information for Masterys BC+ and GP4 UPS, such as serial numbers and device locations.
Describes the status bits for Masterys BC+ and GP4 UPS, covering output, functioning, and device states.
Details additional programmable status bits for Masterys BC+ and GP4 UPS, used for custom inputs/outputs.
Summarizes the operational status of units within the Masterys BC+ and GP4 systems.
Lists critical alarms for Masterys BC+ and GP4 UPS, categorized by load, mode, service, battery, and rectifier.
Covers additional programmable alarm bits for Masterys BC+ and GP4 UPS, enabling custom event monitoring.
Provides a synthesized view of general alarms for each unit in the Masterys BC+ and GP4 systems.
Details UPS measurements for Masterys BC+ and GP4, including load, voltage, current, and temperature readings.
Defines commands available for Masterys BC+ and GP4 UPS, such as eco mode control and reset functions.
Specifies the format for reading and writing UPS clock and date information for Masterys BC+ and GP4.
Lists the Modbus function codes utilized in the protocol, such as READ data and WRITE commands.
Summarizes the byte structure and components of Modbus frames for different function codes.
Explains Modbus error codes and their corresponding conditions and specific addresses.
Details the CRC-16-CC-ITT calculation method used for Modbus message integrity.
To Next Page
