25
HCD-FLX5D/FLX7D
[DVD SHIP MODE (NO MEMORY CLEAR) ]
• This mode moves the optical pick-up to the position durable to
vibration. Use this mode when returning the set to the customer
after repair.
Procedure:
1. Press the [I/ ] button to turn the power on.
2. Press the [DVD] and [I/ ] buttons simultaneously.
3. After the “STANDBY” display blinks, a message “LOCK” is
displayed on the fluorescent indicator tube, and the CD ship
mode is set.
[VACS ON/OFF MODE]
• This mode is used to switch on or off the VACS (Variable At-
tenuation Control System).
Procedure:
1. Press two buttons of > and [A ] for more than 1 second
simultaneously.
2. When VACS is switch on, it displays “VACS OFF”.
When VACS is switch off, it displays “VACS O”.
[CD REPEAT 5 LIMIT OFF MODE]
Number of repeat for CD playback is 5 times when the repeat
mode is “REPEAT”. This mode enables CD to repeat playback for
limitless times.
Procedure:
1. Press the [I/ ] button to turn the power on, and press the [DVD]
button to select the function “DVD”.
2. Press two buttons of > and [CD SYNC HI-DUB] for more
than 1 second simultaneously to enter the CD repeat 5 limit off
mode.
3. To release this mode, operate the cold reset. (Refer to the “MC
COLD RESET”)
[DISC TRAY LOCK]
Procedure:
1. Press the [I/ ] button to turn the power on.
2. Press the [DVD] button to select the function “DVD”.
3. Press two buttons of Z (DVD) and x simultaneously for five
seconds.
4. The message “LOCKED” is displayed and the tray is locked.
(Even if exiting from this mode, the tray is still locked)
5. To exit from this mode, press two buttons of Z (DVD)
and x simultaneously for five seconds again.
6. The message “UNLOCKED” is displayed and the tray is un-
locked.
Volume check:
1. When the
[VOLUME] knob is turned clockwise even slightly,
the sound volume increases to its maximum and a message
“VOLUME MAX” appears for two seconds, then the display
returns to the original display.
2. When the [VOLUME] knob is turned counterclockwise even
slightly, the sound volume decreases to its minimum and a
message “VOLUME MIN” appears for two seconds, then the
display returns to the original display.
Tuner Function
1. In the test mode, the default-preset channel is called even when
the TUNER is selected and an attempt is made to call the pre-
set channel that has been stored in memory. (It means that the
memory is cleared)
2. The minimum, center and maximum frequency of each band
is set then.
4. Tape Recording Test
Procedure:
1. Enter the MC Test Mode.
2. Load tapes in both tape decks A and B.
3. Press the REC button to start recording.
4. Pressing the
–
m or M
+
buttons during recording returns
the tape to the recording start position and stops it at this posi-
tion.
5. Pressing the “High Speed Dubbing” key while playing back
the tape of deck B switches the playback speed between “Nor-
mal Speed” and “High Speed”.
Note:
When the playback direction of the tape is set to other than “ONY WAY”,
the restriction on the number of times playback which can be repeated
will be cleared.
5. AMS Test Mode
Procedure:
1. Enter the MC Test Mode and press the [TAPE A/B] button to
set the TAPE function.
2. Insert a test tape AMS-110A or AMS-120 to deck A.
3. Press the > button to enter the AMS test mode.
4. After a tape is rewound first, the FF AMS is checked, and the
mechanism is shut off after detecting the AMS signal the AMS
signal twice.
5. Then the REW AMS is checked and the mechanism is shut off
after detecting the AMS signal twice.
6. When the check is complete, a message of either OK or NG
appears.
6. ALC MODE
Procedure:
1. Enter the MC Test Mode and press the [REC PAUSE/START]
button 2 times to recording start.
2. While pressing the . button, ALC is on.
(normaly, ALC is off in recording state.)
[DVD SHIP MODE (MEMORY CLEAR) ]
• This mode moves the optical pick-up to the position durable to
vibration. Use this mode when returning the set to the customer
after repair.
Procedure:
1. Press the [I/ ] button to turn the power on.
2. Press three buttons x , [CD SYNC HI-DUB] and [DVD]
simultaneously.
3. After the “STANDBY” display blinks, a message “LOCK” is
displayed on the fluorescent indicator tube, and the CD ship
mode is set.
1
Z
1
1
1
1
w
w
w
.
x
i
a
o
y
u
1
6
3
.
c
o
m
Q
Q
3
7
6
3
1
5
1
5
0
9
9
2
8
9
4
2
9
8
T
E
L
1
3
9
4
2
2
9
6
5
1
3
9
9
2
8
9
4
2
9
8
0
5
1
5
1
3
6
7
3
Q
Q
TEL 13942296513 QQ 376315150 892498299
TEL 13942296513 QQ 376315150 892498299
http://www.xiaoyu163.com
http://www.xiaoyu163.com
To Next Page
Loading...
