35
Chapter 2 Menu
Assigning the Remote Control Functions
(SET UP 2) — REMOTE Menu
The remote control functions are set with the
REMOTE menu. With this monitor, both serial remote
control (REMOTE 1) and parallel remote control
(REMOTE 2) are possible. It is possible to
simultaneously use the REMOTE 1, and REMOTE 2
provided with BKM-10R/11R, the integrated control
unit monitors HDM-14E5U, BVM-14E5U/14E5E/
14F5U/14F5E/14G5U/14G5E/14G5A, for control, but
commands from REMOTE 2 have priority. Therefore,
it is impossible for the control panel or REMOTE 1 to
change items set by REMOTE 2.
There is no priority order between commands from
REMOTE 1 and the BKM-10R/11R control panel; it is
possible to set APERTURE to ON from REMOTE 1
and then set it to OFF with a control panel operation.
About monitor address and group numbers
The monitor control units BKM-10R/11R or control
unit monitors HDM-14E5U, BVM-14E5U/14E5E/
14F5U/14F5E/14G5U/14G5E/14G5A are able to
control up to 32 monitors connected via serial remote
connector (using the REMOTE 1 connector). By
giving each monitor a monitor address and group
number, it is possible to control just a specific monitor
or monitor group.
With the REMOTE menu, each monitor can be set
with a monitor address and group number, between 1
and 99.
The ADDRESS menu is used to select a particular
monitor or group by entering a monitor number or
group number.
For information about the ADDRESS menu, see “Selecting
the Monitor to Control —ADDRESS Menu” on page 49.
The address number must differ from one monitor to
another. If two or more monitors have the same address
number, an operation error occurs.
Overview
Structure of the REMOTE Menu
[C2]
Level 1 Level 2 Level 3
INPUT CONFIGURATION [C1] MONITOR ADDRESS
REMOTE [C2] REMOTE 1 CONFIG [C21] GROUP ADDRESS
PASSWORD [C3] REMOTE MODE [C211]
SYSTEM CONFIGURATION [C4] REMOTE 2 CONFIG [C22] 1 PIN [C221]
ON SCREEN SET [C5] REMOTE 2 2 PIN
ALIGNMENT [C6] 3 PIN
EXTEND MENU [C7] 4 PIN
5 PIN
6 PIN
7 PIN
8 PIN
Setting Lists of the REMOTE Menu
This section explains the setting lists displayed in the
menu.
How to read the setting lists
•For purposes of explanation, each setting list is
preceded by a menu number. These numbers are not
displayed on the screen.
For more information about the menu number, see “About
menu numbers” on page 19.
•The arrow mark (÷) refers you to another setting list
that appears after you make the setting, or to an
operation that is carried out as a result of the setting.
When there is no arrow mark, the menu does not have
any sub-list.
36
Chapter 2 Menu
[C2] REMOTE menu
Select the type of remote control.
REMOTE 1 CONFIG: Set the address and group
number of the monitor controlled via the
REMOTE 1 (serial remote control) connector.
÷[C21]
REMOTE 2 CONFIG: Set the pin assignments for
the REMOTE 2 (parallel remote control)
connector. ÷[C22]
REMOTE 2: Select whether parallel remote control
will be used or not (ON or OFF).
[C21] REMOTE 1 CONFIG menu
Set the monitor address and group number.
MONITOR ADDRESS: Enter a number.
GROUP ADDRESS: Enter a number.
REMOTE MODE: Select the remote mode.
÷[C211]
[C22] REMOTE 2 CONFIG
Select the REMOTE 2 connector pins for which you
want to change the function. The factory settings for
each pin are given below. ÷[C221]
1 PIN: CH01
2 PIN: CH02
3 PIN: EXT SYNC
4 PIN: MONO
5 PIN: SAFE AREA ON
6 PIN: unused
7 PIN: unused
8 PIN: TALLY
[C211] REMOTE MODE menu
Select a remote mode according to the type of
monitors connected through the REMOTE 1
connector.
When only Sony BVM-xxE/F/G or HDM-xxE series
monitors are connected: set REMOTE MODE to
0.
When a Sony BVM-xx11/16 series monitor or a
Sony PVM monitor (with BKM-103 Serial
Remote Interface Kit installed) is connected: set
REMOTE MODE to 1 and enter a number over 64
as the MONITOR ADDRESS for each connected
Sony BVM-xxE/F/G and HDM-xxE series
monitor.
[C221] 1-8 PIN (1/2) menu
Assign a function to the selected pin.
CH: Select a channel number. Enter the desired
channel number with the numeric keypad.
----: Set to unused.
UNDER SCAN: Set underscan on or off.
16:9: Set a 16:9 aspect ratio on or off.
H DELAY: Set the horizontal sync display on or off.
V DELAY: Set the vertical sync display on or off.
EXT SYNC: Set the synchronization to external sync
signals enabled or disabled.
APERTURE: Set the correction of frequency
characteristics enabled or disabled.
MONO: Set monochrome display on or off.
1-8 PIN (2/2) menu
Assign a function to the selected pin.
BLUE ONLY: Set the blue signal pictures display
(monochrome) on or off.
R OFF: Set cutting red beams enabled or disabled.
G OFF: Set cutting green beams enabled or disabled.
B OFF: Set cutting blue beams enabled or disabled.
SAFE AREA ON: Set the safe area display on or off.
CAPTION VISION: Set Caption Vision on or off.
TALLY: Set tally signals on or off.
DEGAUSS: Set degaussing on or off.
POWER OFF: Set the monitor power on or off.
Assigning the Remote Control Functions (SET UP 2) REMOTE Menu
To Next Page
Loading...
