Spirax Sarco ILVA20 - Commissioning Mode

IM-P337- 6 9 EMM Issue 2
42
7.2 Commissioning mode
The commissioning mode is used to zero the pressure sensor and DP sensor, enable the temperature
sensor (for superheat/heat metering applications), set and test the outputs and change the pass code.
                  
navigation, i.e. to go deeper into the menu the right hand key is pressed, to scroll up and down the menu the
up and down keys are pressed and to exit from a sub-menu the left key is pressed. Any data is entered using


To enter the commissioning mode press and hold down the 'OK' key for 3 seconds. The display then shows
8888.
Followed by:

The default factory set pass code is 7452. (This can be changed from within the commissioning mode).

and right keys to move the cursor. Pressing 'OK' will enter the pass code.
If an incorrect pass code is used the display will automatically return to the run mode.
After the correct pass code is entered the display shows:
25
PRES
0
8888
ON
OFF
StEAM
HEAt XXXX%
SENSR
tEMP
SENSR
COMMS
ALARM
In-PUtS
x.xxSec
xx.xxmA
dELAy
XXXX
PRES
0 CAL
PRES
25 CAL
8888
PRES
SENSR
tEMP
SENSR
ON
OFF
STEAM
HEAT
XXXX%
COMMS
ALARM
dISP
dP
X.X.X
25
PRES
0
8888
ON
OFF
StEAM
HEAt XXXX%
SENSR
tEMP
SENSR
COMMS
ALARM
In-PUtS
x.xxSec
xx.xxmA
dELAy
XXXX
PRES
0 CAL
PRES
25 CAL
8888
PRES
SENSR
tEMP
SENSR
ON
OFF
STEAM
HEAT
XXXX%
COMMS
ALARM
dISP
dP
X.X.X
25
PRES
0
8888
ON
OFF
StEAM
HEAt XXXX%
SENSR
tEMP
SENSR
COMMS
ALARM
In-PUtS
x.xxSec
xx.xxmA
dELAy
XXXX
PRES
0 CAL
PRES
25 CAL
8888
PRES
SENSR
tEMP
SENSR
ON
OFF
STEAM
HEAT
XXXX%
COMMS
ALARM
dISP
dP
X.X.X
To exit from the commissioning mode at any stage, continually pressing the left
key will return to the run mode.

Pressing the right arrow button enters a particular sub-menu.
25
PRES
0
8888
ON
OFF
StEAM
HEAt XXXX%
SENSR
tEMP
SENSR
COMMS
ALARM
In-PUtS
x.xxSec
xx.xxmA
dELAy
XXXX
PRES
0 CAL
PRES
25 CAL
8888
PRES
SENSR
tEMP
SENSR
ON
OFF
STEAM
HEAT
XXXX%
COMMS
ALARM
dISP
dP
X.X.X
25
PRES
0
8888
ON
OFF
StEAM
HEAt XXXX%
SENSR
tEMP
SENSR
COMMS
ALARM
In-PUtS
x.xxSec
xx.xxmA
dELAy
XXXX
PRES
0 CAL
PRES
25 CAL
8888
PRES
SENSR
tEMP
SENSR
ON
OFF
STEAM
HEAT
XXXX%
COMMS
ALARM
dISP
dP
X.X.X
25
PRES
0
8888
ON
OFF
StEAM
HEAt XXXX%
SENSR
tEMP
SENSR
COMMS
ALARM
In-PUtS
x.xxSec
xx.xxmA
dELAy
XXXX
PRES
0 CAL
PRES
25 CAL
8888
PRES
SENSR
tEMP
SENSR
ON
OFF
STEAM
HEAT
XXXX%
COMMS
ALARM
dISP
dP
X.X.X
25
PRES
0
8888
ON
OFF
StEAM
HEAt XXXX%
SENSR
tEMP
SENSR
COMMS
ALARM
In-PUtS
x.xxSec
xx.xxmA
dELAy
XXXX
PRES
0 CAL
PRES
25 CAL
8888
PRES
SENSR
tEMP
SENSR
ON
OFF
STEAM
HEAT
XXXX%
COMMS
ALARM
dISP
dP
X.X.X
25
PRES
0
8888
ON
OFF
StEAM
HEAt XXXX%
SENSR
tEMP
SENSR
COMMS
ALARM
In-PUtS
x.xxSec
xx.xxmA
dELAy
XXXX
PRES
0 CAL
PRES
25 CAL
8888
PRES
SENSR
tEMP
SENSR
ON
OFF
STEAM
HEAT
XXXX%
COMMS
ALARM
dISP
dP
X.X.X
25
PRES
0
8888
ON
OFF
StEAM
HEAt XXXX%
SENSR
tEMP
SENSR
COMMS
ALARM
In-PUtS
x.xxSec
xx.xxmA
dELAy
XXXX
PRES
0 CAL
PRES
25 CAL
8888
PRES
SENSR
tEMP
SENSR
ON
OFF
STEAM
HEAT
XXXX%
COMMS
ALARM
dISP
dP
X.X.X
8888
25
PRES
0
8888
ON
OFF
StEAM
HEAt XXXX%
SENSR
tEMP
SENSR
COMMS
ALARM
In-PUtS
x.xxSec
xx.xxmA
dELAy
XXXX
PRES
0 CAL
PRES
25 CAL
8888
PRES
SENSR
tEMP
SENSR
ON
OFF
STEAM
HEAT
XXXX%
COMMS
ALARM
dISP
dP
X.X.X
25
PRES
0
8888
ON
OFF
StEAM
HEAt XXXX%
SENSR
tEMP
SENSR
COMMS
ALARM
In-PUtS
x.xxSec
xx.xxmA
dELAy
XXXX
PRES
0 CAL
PRES
25 CAL
8888
PRES
SENSR
tEMP
SENSR
ON
OFF
STEAM
HEAT
XXXX%
COMMS
ALARM
dISP
dP
X.X.X