Stanley FATMAX V20 SFMCPW1500 - Preparing Spray Lance; Cleaning a Surface; Moving the Pressure Washer; Shutdown Procedure

14
ENGLISH
(Original instructions)
DEUTSCH

CAUTION: Do not hold the trigger when closing the
battery portcover.
1. Lift and hold the battery port cover
14
up to expose the
batteryports.
2. Align the battery packs
32
with the rails inside the battery
port and slide them in until the battery packs are firmly
seated in the tool and ensure that they will notdisengage.
3. Close the battery port cover
14
. Ensure the cover is fully
latched into position before startingtool.
NOTE: The unit will not operate if the battery door is not
fullyclosed.
To Remove the Battery Packs
1. Lift and hold the battery port cover
14
up to expose the
battery packs
32
.
2. Press the battery release buttons
33
on the battery
packs
32
and firmly pull the battery packs out oftool.
3. Insert the batteries into a charger as described in the
charger section of thismanual.
Proper Hand Position (Fig.L)

WARNING: To reduce the risk of serious personal injury,
ALWAYS use proper hand position as shown.

WARNING: To reduce the risk of serious personal injury,
ALWAYS hold securely in anticipation of a suddenreaction.
Proper hand position requires one hand on the spray gun
handle grip
8
and the other hand on the spray gun
7
.
Speed Selector Switch (Fig.A, M)
This pressure washer gives you the choice to operate at a high
pressure or lower pressure for more delicate jobs, and can also
boost pressure for high-performancecleaning.
The speed switch selector
12
toggles to three positions;
‑ Off,centred.
‑ HI, rightside.
‑ LO, leftside.
To turn the pressure washer ON, toggle the speed switch
selector
12
to the right or leftpositions.
To turn the pressure washer OFF, toggle the speed switch
selector
12
to the centreposition.
For higher pressure washing, press the speed switch
selector
12
to the right to the "HI" position. This mode is best
for applications that need higherPSI.
For lower pressure washing, press the speed switch
selector
12
to the left to the "LO" position. This mode is best
for projects that require a more delicate cleaning. This mode
also generally offers moreruntime.
NOTE: When in "HI" mode, runtime will be decreased as
compared to when pressure washer is in "LO"mode.
To activate Boost mode, press the boost button
13
, the
green LED will illuminate when activated. This mode is best for
applications that require maximum availablePSI.
NOTE: Boost mode will only function for up to five minutes.
You can press the boost button again to exit boost mode
before five minutes and you will go back to the mode the
speed switch selector
12
is set to. When you near the end of
five minutes the green LED will start to flash, and the unit will
return to the mode the speed switch selector is set to after
boost mode timesout.
NOTE: After boost mode is used for a full five minutes, the
unit requires a cool down cycle before boost mode can be
reactivated. The green LED will flash, for approximately eight
minutes, until the cool down cycle is complete. Once the cool
down cycle is complete, the green LED will turn off. Boost
mode can now be used again by pressing the boostbutton.
NOTE: The unit can be used in high or low mode during the
cool downcycle.
Pressure Washing (Fig.A–M)

WARNING: To reduce the risk of serious personal
injury, turn unit off and remove the battery pack
before making any adjustments or removing/
installing attachments or accessories. An accidental
start‑up can causeinjury.
Preparing Surface for Cleaning
• Remove objects from the area which could create a hazard
such as children's toys or outdoor furniture.
• Insure that all doors and windows are closed tight.
Protect all plants and trees in the adjacent area with a
drop cloth ensuring that they will not be harmed by
anyoverspray.
• Pre-rinse cleaning area with freshwater.
• Use only detergents formulated for pressurewashers.
• Always test detergent in an inconspicuous area beforeuse.
Preparing Pressure Washer Unit for Use

DANGER: Risk of fluid injection and laceration. When
using the high‑pressure setting, DO NOT allow the
high‑pressure spray to come in contact with unprotected
skin, eyes, or with any pets or animals. Serious injury
willoccur.

CAUTION: Before operation:
1 . Connect the high pressure hose to the pressure washer
and the pressure wand. For instructions on connecting
the high pressure hose to the pressure washer and pressure
wand, please refer to Attaching High Pressure Hose
under Assembly andAdjustments.
2 . Connect the water supply to the pressure washer. For
instructions on connecting the water supply to the pressure
washer, please refer to Attaching Garden Hose under
Assembly andAdjustments.
3 . Lift and hold the battery port cover
14
up to expose the
batteryports. Install the two battery packs
32
. Close the
battery port cover. Ensure the cover is fully latched into
position, please refer to To Install the Battery Packs
under Installing and Removing the BatteryPacks.