Stanley FATMAX V20 SFMCPW1500 - Nozzle Cleaning; Suction Hose and Filter; Maintenance and Cleaning

13
ENGLISH
(Original instructions)
2. Release the button to lock the nozzle inplace.
3. Give the nozzle a firm tug to ensure the nozzle is locked
intoplace.
Nozzle type Suitable applications
Adjustable (Spray fan/Pencil)
Nozzle
For gentle wide angle
cleaning
Turbo/Rotating Nozzle For abrasive cleaning
NOTE: The Turbo/Rotating nozzle
23
(refer to Fig. G2) is
suitable for cleaning concrete and masonry. We do not
recommend using this nozzle for car/vehicle cleaning as it can
cause damage to thesurface.
Adjusting Spray Pattern of the Adjustable
Nozzle from Spray Fan to Pencil (Fig.G1)
The angle of spray coming out of the spray lance may be
adjusted by rotating the nozzle. This will vary the spray pattern
from approximately a 0° narrow high impact stream to a 60°
wide fan spray. A wide fan pattern distributes the impact of
the water over a larger area, resulting in excellent cleaning
action with a reduced risk of surface damage. Large surface
areas can be cleaned more quickly using a wide fan pattern.
A narrow pencil jet stream distributes the impact of the water
in a concentrated area, resulting in a high impact force on
the cleaning surface. Use a narrow pencil jet stream for deep
cleaning in a concentrated area. However, use it cautiously, as
it may damage somesurfaces.
To Attach the Self Priming Suction Hose
(Fig.H)
Use the suction hose to pull water from a bucket or other fresh
watersource.
NOTICE: Do not use to suction soap, chemicals, dirty
or corrosive liquids, such as window cleaner, plant food,
fertilizers or bleach. Do not use with saltwater.
NOTE: Avoid cross threading when installing the suction hose.
Cross threading will causeleaks.
1. To connect the self priming suction hose
2
to the
pressurewasherunit, thread the suction hose collar
31
onto the water intake
18
.
2. Securely tighten the suction hose collar
31
byhand.
NOTE: Always disconnect the suction hose afterusage.
3. Place other end of suction hose, with the suction hose
filter
4
on it, into a container of fresh water or a fresh
watersource.
4. Adjust the float ball
3
on the suction hose so the suction
hose filter
4
stays covered in theliquid.
5. Select the correct nozzle to be used. Refer to
AttachingNozzles.
6. After the job being performed is complete, place the
suction hose into a container of clean water and draw the
clean water through the system torinse.
Removing Soap Bottle from Storage (Fig. I )
Always completely empty the soap bottle
26
beforestoring.
1. Unlock the telescoping handle
16
, and slide it upwards so
you can access the soap bottle
26
.
2. To remove the soap bottle
26
from the built-in storage
space in the pressure washer unit, grasp the soap
bottle with one hand and pull it out and away from the
pressure washerunit.
3. To place the soap bottle
26
into its storage slot, press the
soap bottle firmly into the storage slot until it snaps into
the built-in storage space in the pressure washerunit.
4. Ensure that soap bottle is secured into the storage position
by gently tugging on the soapbottle.
Attaching Soap Bottle (Fig.J)
1. To connect the soap bottle
26
to the spray gun 
7
 , pull
the nozzle button
6
toward the spray gun and insert the
soap bottle.
2. Release the quick connect collar to lock the soap bottle
in place.
3. Give the soap bottle a firm tug after the quick connect
collar has locked intoplace to ensure the soap bottle is
locked intoplace.
NOTE: The soap bottle should be positioned with the bottle
towards the ground. Do not position the soap bottle above the
spray lance as this will lead to soap dripping on the spraylance.
OPERATION

WARNING: To reduce the risk of serious personal
injury, turn unit off and remove the battery pack
before making any adjustments or removing/
installing attachments or accessories. An accidental
start‑up can causeinjury.
Installing and Removing the Battery Packs
(Fig.K)
This pressure washer is designed to operate on two battery
packs of equal capacity. The pressure washer will not operate
on a single battery pack, and if using different capacity battery
packs, the smaller capacity battery pack, when depleted, will
cause the unit to turnoff.
NOTE: For best results, make sure your battery packs are both
fullycharged.
For optimum performance and runtime, we recommend
using 4.0Ah (SFMCB204) or 6.0Ah (SFMCB206) battery packs.
The pressure washer requires 2x batteries torun.
To Install the Battery Packs

WARNING: Ensure speed selector switch is in the OFF,
centred position, before installing batterypacks.

CAUTION: Unit stops running when the battery port
cover is open. If the speed selector switch is in the HI or
LO position the unit will power ON when the battery port
covercloses.