Supermicro X10DAL-i - 2-7 Connecting Cables

Chapter 2: Installation
2-25
BT1
JPCIE3
LEDPWR
I-SGPIO2
LE6
JBT1
BIOS LICENSE
JPI2C1
JTBT1
J24
JPWR1
JPWR2
JF1
JD1
JHD_AC1
JSPDIF_OUT
JSPDIF_IN
J21
JL1
JSD1
JSD2
JSTBY1
JTPM1
JVRM2
JVRM1
JPAC1
JPL2
JPL1
JPUSB1
JBR1
JI2C2
JPME2
JI2C1
J23
SP1
FAN3
FANA
FAN6
FAN4
FAN2
FAN1
MAC CODE
X10DAL-i
BAR CODE
AUDIO FP
HD AUDIO
(3.0)
USB5/6
(3.0)
USB7/8(3.0)
USB1/2
USB0
USB3/4
S-SATA2
S-SATA0
S-SATA1
S-SATA3
I-SATA5
CPU1 SLOT1 PCI-E 3.0 X8 (IN X16)
I-SATA4
CPU2 SLOT2 PCI-E 3.0 X4 (IN X8)
I-SATA3
I-SATA2
I-SATA1
CPU1 SLOT3 PCI-E 3.0 X16
I-SATA0
CPU1 SLOT5 PCI-E 3.0 X16
P2-DIMME1
P1-DIMMC1
P2-DIMMF1
P1-DIMMD1
P2-DIMMH1
P1-DIMMB1
P1-DIMMA1
LAN2
P2-DIMMG1
LAN1
COM1
I-SGPIO1
S-SGPIO
PCH SLOT6 PCI-E 2.0 X4 (IN X8)
JWD1
Rev. 1.02
1
FAN5
CPU1
CPU2
Battery
PCH
BIOS
Warning: To provide adequate power to the
motherboard, be sure to connect the 24-pin
ATX PWR (J24) and two 8-pin PWR connectors
(JPWR1, JPWR2) to the power supply. Failure
to do so will void the manufacturer warranty on
your power supply and motherboard.
2-7 Connecting Cables
Power Connectors
A 24-pin main power supply connector
(J24) and two 8-pin CPU PWR connectors
(JPWR1, JPWR2) are located on the moth-
erboard. These power connectors meet the
SSI EPS 12V specication. These power
connectors must also be connected to your
power supply. See the table on the right for
pin denitions.
ATX Power 24-pin Connector
Pin Denitions
Pin # Denition Pin # Denition
13 +3.3V 1 +3.3V
14 -12V 2 +3.3V
15 COM 3 COM
16 PS_ON 4 +5V
17 COM 5 COM
18 COM 6 +5V
19 COM 7 COM
20 Res (NC) 8 PWR_OK
21 +5V 9 5VSB
22 +5V 10 +12V
23 +5V 11 +12V
24 COM 12 +3.3V
12V 8-pin PWR Con-
nector
Pin Denitions
Pin # Denition
1 through 4 Ground
5 through 8 +12V
A. J24: 24-pin ATX PWR
(Req'd)
B. JPWR1: 8-pin Proces-
sor PWR (Req'd)
C. JPWR2: 8-pin Proces-
sor PWR (Req'd)
A
B
C
(Required)