Supermicro X10DAL-i - I-SGPIO 1;2 & S-SGPIO Headers, SATA_DOM Power Connectors

Chapter 2: Installation
2-29
BT1
JPCIE3
LEDPWR
I-SGPIO2
LE6
JBT1
BIOS LICENSE
JPI2C1
JTBT1
J24
JPWR1
JPWR2
JF1
JD1
JHD_AC1
JSPDIF_OUT
JSPDIF_IN
J21
JL1
JSD1
JSD2
JSTBY1
JTPM1
JVRM2
JVRM1
JPAC1
JPL2
JPL1
JPUSB1
JBR1
JI2C2
JPME2
JI2C1
J23
SP1
FAN3
FANA
FAN6
FAN4
FAN2
FAN1
MAC CODE
X10DAL-i
BAR CODE
AUDIO FP
HD AUDIO
(3.0)
USB5/6
(3.0)
USB7/8(3.0)
USB1/2
USB0
USB3/4
S-SATA2
S-SATA0
S-SATA1
S-SATA3
I-SATA5
CPU1 SLOT1 PCI-E 3.0 X8 (IN X16)
I-SATA4
CPU2 SLOT2 PCI-E 3.0 X4 (IN X8)
I-SATA3
I-SATA2
I-SATA1
CPU1 SLOT3 PCI-E 3.0 X16
I-SATA0
CPU1 SLOT5 PCI-E 3.0 X16
P2-DIMME1
P1-DIMMC1
P2-DIMMF1
P1-DIMMD1
P2-DIMMH1
P1-DIMMB1
P1-DIMMA1
LAN2
P2-DIMMG1
LAN1
COM1
I-SGPIO1
S-SGPIO
PCH SLOT6 PCI-E 2.0 X4 (IN X8)
JWD1
Rev. 1.02
1
FAN5
CPU1
CPU2
Battery
PCH
BIOS
C
A
B
A. I-SGPIO1
B. I-SGPIO2
C. S-SGPIO
D. JSD1
E. JSD2
I-SGPIO 1/2 & S-SGPIO Headers
Three SGPIO (Serial-Link General
Purpose Input/Output) headers are
located on the motherboard. These
headers support Serial_Link interface
for onboard SATA/SAS connections
when available. See the tables on the
right for SGPIO support and for pin
denitions.
Note: NC= No Connection
I-SGPIO 1/2 & S-SGPIO
Pin Denitions
Pin # Denition Pin Denition
1 NC 2 NC
3 Ground 4 Data
5 Load 6 Ground
7 Clock 8 NC
D
E
SATA_DOM Power Connectors
Two 3-pin power connectors (JSD1/
JSD2) are used to provide power to
onboard SATA DOM (Disk_On_Mod-
ule) devices. Connect appropriate
cables here to provide power for your
SATA DOM devices. See the layout
below for the locations of the power
connectors.
SATA DOM/Connectors
Pin Denitions
Pin # Denition
1 +5V
2 Ground
3 Ground
I-SGPIO 1/2 & S-SGPIO
Support
I-SGPIO 1 I-SATA 0-3 supported
I-SGPIO 2 I-SATA 4/5 supported
S-SGPIO S-SATA 0-3 supported