Tally T2265plus - Terminating Hex-Dump

Tally T2265plus

196 pages

Save Page as PDF

To Next Page

To Next Page

To Previous Page

To Previous Page

Loading...

User guide Advanced menu

101

Terminating Hex-Dump Hex-Dump mode can only be terminated by switching off the printer.

If you want to stop the Hex-Dump printout before switching off

the printer, press the key Online and then the key LF/FF (4)

once.

Table of Contents

Default Chapter3
- Table of Contents3
Introduction11
- Printer Features11
- Symbols Used11
- About this Manual12
Printer at a Glance13
- Printer in Tractor Mode14
- Printer in Single-Sheet Mode14
- Paperway15
Installation17
- Unpacking the Printer17
- Placing Your Printer18
- Checking the Printer Voltage19
- Connecting the Printer19
- Switching on the Printer20
Inserting the Ribbon Cassette21
- Installing the Ribbon Cassette the First Time21
- Changing the Ribbon Cassette27
Printer Drivers33
- Installing a Printer Driver in Windows 95/98/ME33
- Installing a Printer Driver in Windows 2000/2003/XP33
- Installing a Printer Driver in Windows 735
- Installing a Printer Driver in Windows Vista36
- Other Operating Systems37
- Changing Printer Settings38
  - Form Settings (Windows Windows 2000/Xp/Vista/Windows 7)38
- Loading Optional Firmware39
  - Troubleshooting39
The Control Panel41
- The LC Display42
- Online Mode43
- Offline Mode43
- Setup Mode44
- Messages in the LC Display45
- Key Functions When Turning on the Printer46
Paper Handling47
- Changing the Paper Type47
  - Changing the Paper Type in the Setup Menu48
- Loading Paper49
  - Fanfold Paper49
  - Single Sheets51
- Paper Transport53
- Moving the Paper to the Tear Position54
- Removing Paper55
Settings57
- Setting the Print Head Gap57
- Setting the Tear Position58
- Setting the First Printing Line (TOF)59
- Selecting Character Density and Font60
Model61
- Introduction61
  - Rear Tractor Paper Path61
- Loading Paper into the Rear Tractor62
- Paper Guiding Bracket64
- Selecting the Rear Tractor64
The Menu67
- Programming Via the Control Panel67
- Enabling Access to Menu Mode67
- Calling up the Menu67
- Menu Configurations68
- Menu Handling69
- Menu Structure72
- Menu Parameters73
- Menu Settings (Example)104
Advanced Menu107
- Test Functions107
  - Printer Self-Test (Rolling ASCII)108
    - Exiting Rolling ASCII Test Mode109
  - Interface Test (Hex-Dump)110
    - Printout in Hex-Dump110
    - Terminating Hex-Dump111
- Advanced Settings112
Troubleshooting127
- General Print Problems128
- Problems with the Print Quality131
- Error Messages Via the Display132
- Additional Display Messages135
Care and Maintenance137
- Replacing the Fuse137
- Cleaning the Housing138
- Cleaning the Interior138
- Cleaning the Platen139
- Ribbon139
- Cleaning the Upper Friction140
- Carriage Shafts140
Specifications141
- Printer Specifications141
- Interface Specifications145
- Paper Specifications146
Character Sets149
- MTPL Standard Character Set150
- MTPL, International Substitution Characters151
- OCR-A Character Set152
- OCR-B Character Set153
- Available Character Sets and Fonts154
Emulations157
- General157
- Escape Sequences157
- What Are Escape Sequences158
- How Are Escape Sequences Used159
  - Mtpl159
- List of Available Control Codes160
- Barcode170
Interfaces175
- Parallel Interface176
  - Connector Assignment176
- Ethernet Interface177
- Optional Serial Interface V.24/RS232C179
Options and Accessories183
- Options183
- Accessories185
  - Ribbon Cassettes185
  - Programming Manuals185
Index187

Related product manuals

Preview: Tally T2265 SprintPro

Tally T2265 SprintPro

Preview: Tally T2240

Preview: Tally T2240/24

Preview: Tally T2030

Preview: Tally T2040

Preview: Tally T2380

Preview: Tally T2150

Preview: Tally T6215

Preview: Tally Dascom 1125

Tally Dascom 1125

Preview: Tally DT-230